310T Prep – Questions With Expert Solutions
Save Groups
Terms in this set (341)
1. Which of the following clutch b. clutch friction disc
components is a driven member?!
a. clutch cover
b. clutch friction disc
c. intermediate plate
d. pressure plate
2. Which of the following is not a part d. adapter ring
of the clutch cover assembly?!
a. pressure spring
b. release lever
c. pressure plate
d. adapter ring
3. Which of the following clutch a. clutch friction disc
components is splined to the input
shaft of the transmission?!
a. clutch friction disc
b. pressure plate
c. release bearing
d. flywheel
4. What is the function of a current a. minimize gear clash during a neutral to first gear
clutch brake used in a heavy-duty shift
drivetrain?!
a. minimize gear clash during a neutral
to first gear shift
b. minimize gear clash during
downshifts to all ratios
c. minimize gear clash during upshifts
to all ratios
d. none of the above
,5. Which of the following driving d. all of the above
procedures will result in clutch or
driveline damage?!
a. driving with a foot on the clutch
pedal
b. using the clutch as a brake to hold
the truck on a hill and incline
c. coasting downhill with the
transmission in gear and the clutch
disengaged
d. all of the above
6. Which of the following could be a d. all of the above
cause of poor clutch release?!
a. damaged drive pins
b. worn clutch linkage
c. worn release bearing
d. all of the above
7. How often should a clutch be d. all of the above
inspected and lubricated?!
a. every month
b. every 6,000 to 10,000 miles
c. any time the chassis is lubricated
d. all of the above
8. When adjusting clutch linkage, a. Technician A only
Technician A says that pedal free
travel should be about 1½ to 2
inches. Technician B says that free
travel should be more than ½ inch
measured at the release
forks. Who is correct?!
a. Technician A only
b. Technician B only
c. both A and B
d. neither A nor B
,9. When servicing clutches, Technician a. Technician A only
A always wears an OSHA-approved
particulate mask.
Technician B uses compressed air to
clean off clutch components before
removing a clutch
pack. Who is correct?!
a. Technician A only
b. Technician B only
c. both A and B
d. neither A nor B
10. In the procedure required to a. Unbolt the clutch from the flywheel
perform a clutch replacement on a
truck, which of the following
steps should be performed first?!
a. Unbolt the clutch from the flywheel.
b. Remove the clutch brake.
c. Install a clutch alignment tool
through the release bearing.
d. Unbolt the transmission bell
housing from the flywheel.
11. On which of the following types of b. pot flywheel
flywheels would the center
intermediate plate be driven by
drive pins?!
a. flat flywheel
b. pot flywheel
c. torque converter
d. all of the above
, 12. Failure analysis determines that the b. Technician B only
facing of a clutch disc has burst.
Technician A says that the
cause is the driver using the clutch as
a brake. Technician B says that the
problem might be the
driver coasting downhill with the
transmission in gear and the clutch
disengaged. Who is correct?!
a. Technician A only
b. Technician B only
c. both A and B
d. neither A nor B
13. When installing a 14-inch clutch, a. Technician A only
Technician A installs new drive pins in
the flywheel. Technician B
files the drive pin slots to ensure that
proper clearances are met. Who is
correct?!
a. Technician A only
b. Technician B only
c. both A and B
d. neither A nor B
14. When regarding the operation of a c. intermediate plate
typical 15½- inch clutch, which of the
following components
constantly rotates at engine rpm?!
a. rear clutch disc
b. front clutch disc
c. intermediate plate
d. clutch brake
Save Groups
Terms in this set (341)
1. Which of the following clutch b. clutch friction disc
components is a driven member?!
a. clutch cover
b. clutch friction disc
c. intermediate plate
d. pressure plate
2. Which of the following is not a part d. adapter ring
of the clutch cover assembly?!
a. pressure spring
b. release lever
c. pressure plate
d. adapter ring
3. Which of the following clutch a. clutch friction disc
components is splined to the input
shaft of the transmission?!
a. clutch friction disc
b. pressure plate
c. release bearing
d. flywheel
4. What is the function of a current a. minimize gear clash during a neutral to first gear
clutch brake used in a heavy-duty shift
drivetrain?!
a. minimize gear clash during a neutral
to first gear shift
b. minimize gear clash during
downshifts to all ratios
c. minimize gear clash during upshifts
to all ratios
d. none of the above
,5. Which of the following driving d. all of the above
procedures will result in clutch or
driveline damage?!
a. driving with a foot on the clutch
pedal
b. using the clutch as a brake to hold
the truck on a hill and incline
c. coasting downhill with the
transmission in gear and the clutch
disengaged
d. all of the above
6. Which of the following could be a d. all of the above
cause of poor clutch release?!
a. damaged drive pins
b. worn clutch linkage
c. worn release bearing
d. all of the above
7. How often should a clutch be d. all of the above
inspected and lubricated?!
a. every month
b. every 6,000 to 10,000 miles
c. any time the chassis is lubricated
d. all of the above
8. When adjusting clutch linkage, a. Technician A only
Technician A says that pedal free
travel should be about 1½ to 2
inches. Technician B says that free
travel should be more than ½ inch
measured at the release
forks. Who is correct?!
a. Technician A only
b. Technician B only
c. both A and B
d. neither A nor B
,9. When servicing clutches, Technician a. Technician A only
A always wears an OSHA-approved
particulate mask.
Technician B uses compressed air to
clean off clutch components before
removing a clutch
pack. Who is correct?!
a. Technician A only
b. Technician B only
c. both A and B
d. neither A nor B
10. In the procedure required to a. Unbolt the clutch from the flywheel
perform a clutch replacement on a
truck, which of the following
steps should be performed first?!
a. Unbolt the clutch from the flywheel.
b. Remove the clutch brake.
c. Install a clutch alignment tool
through the release bearing.
d. Unbolt the transmission bell
housing from the flywheel.
11. On which of the following types of b. pot flywheel
flywheels would the center
intermediate plate be driven by
drive pins?!
a. flat flywheel
b. pot flywheel
c. torque converter
d. all of the above
, 12. Failure analysis determines that the b. Technician B only
facing of a clutch disc has burst.
Technician A says that the
cause is the driver using the clutch as
a brake. Technician B says that the
problem might be the
driver coasting downhill with the
transmission in gear and the clutch
disengaged. Who is correct?!
a. Technician A only
b. Technician B only
c. both A and B
d. neither A nor B
13. When installing a 14-inch clutch, a. Technician A only
Technician A installs new drive pins in
the flywheel. Technician B
files the drive pin slots to ensure that
proper clearances are met. Who is
correct?!
a. Technician A only
b. Technician B only
c. both A and B
d. neither A nor B
14. When regarding the operation of a c. intermediate plate
typical 15½- inch clutch, which of the
following components
constantly rotates at engine rpm?!
a. rear clutch disc
b. front clutch disc
c. intermediate plate
d. clutch brake
