Dell Tech Certification PREP ACTUAL 2026
QUESTIONS AND 100% CORRECT ANSWERS
Save
Terms in this set (53)
If the system is not booting into the Right answer:
operating system, how can you
check if the hard drive is detected? - Go to BIOS
- The HDD indicator light or LED
- From within the Windows (or
other) operating system
- Go to BIOS
- Open the Chassis and Check
,What does Factory Data Reset do Correct answer:
on Dell Venue Tablet?
- Will erase all personal data and downloaded
- Will erase all personal data and applications on the Tablet
downloaded applications on the
Tablet
- Resets the hardware, personal
data and applications are not
affected
-Will allow you to restore the Tablet
to an earlier date
-Erases only personal data, all
downloaded applications will
remain intact
State True or False: Statement is:
Discrete Graphics cards connect to - True
the motherboard of a computer
system using a slot, typically an
Accelerated Graphics Port (AGP) or
a Peripheral Component
Interconnect Express (PCIe)
, Why sometimes the values in BIOS Correct Answer:
cannot be saved and shows as
manufacturing mode? - The systemboard jumper is at SERVICE_MODE
state
- The systemboard jumper is at
CMOS_CLR state
- The systemboard jumper is at
SERVICE_MODE state
- The systemboard is faulty
- THe systemboard jumper is at
PASSWORD-CLR state
Choose all that Apply: Correct Answers:
Which of the following statements
are true about the New PSU BIST? - To restart the PSU BIST: Disconnect the AC
power cord for 15 seconds (PSU BIST reset time),
- During PSU BIST, If PSU LED light and then plug in the AC power cord
will stay ON - PSU is functioning
properly - To start the PSU BIST: Plug in the AC power
cord & note the LED light status
- To restart the PSU BIST :
Disconnect the AC power cord for - Ensure to disconnect the AC power cord from
15 seconds (PSU BIST reset time), the PSU, before starting the PSU BIST
and then plug in the AC power cord
- To start the PSU BIST: Plug in the
AC power cord & note the LED light
status
- Ensure to disconnect the AC
power cord from the PSU, before
starting the PSU BIST
QUESTIONS AND 100% CORRECT ANSWERS
Save
Terms in this set (53)
If the system is not booting into the Right answer:
operating system, how can you
check if the hard drive is detected? - Go to BIOS
- The HDD indicator light or LED
- From within the Windows (or
other) operating system
- Go to BIOS
- Open the Chassis and Check
,What does Factory Data Reset do Correct answer:
on Dell Venue Tablet?
- Will erase all personal data and downloaded
- Will erase all personal data and applications on the Tablet
downloaded applications on the
Tablet
- Resets the hardware, personal
data and applications are not
affected
-Will allow you to restore the Tablet
to an earlier date
-Erases only personal data, all
downloaded applications will
remain intact
State True or False: Statement is:
Discrete Graphics cards connect to - True
the motherboard of a computer
system using a slot, typically an
Accelerated Graphics Port (AGP) or
a Peripheral Component
Interconnect Express (PCIe)
, Why sometimes the values in BIOS Correct Answer:
cannot be saved and shows as
manufacturing mode? - The systemboard jumper is at SERVICE_MODE
state
- The systemboard jumper is at
CMOS_CLR state
- The systemboard jumper is at
SERVICE_MODE state
- The systemboard is faulty
- THe systemboard jumper is at
PASSWORD-CLR state
Choose all that Apply: Correct Answers:
Which of the following statements
are true about the New PSU BIST? - To restart the PSU BIST: Disconnect the AC
power cord for 15 seconds (PSU BIST reset time),
- During PSU BIST, If PSU LED light and then plug in the AC power cord
will stay ON - PSU is functioning
properly - To start the PSU BIST: Plug in the AC power
cord & note the LED light status
- To restart the PSU BIST :
Disconnect the AC power cord for - Ensure to disconnect the AC power cord from
15 seconds (PSU BIST reset time), the PSU, before starting the PSU BIST
and then plug in the AC power cord
- To start the PSU BIST: Plug in the
AC power cord & note the LED light
status
- Ensure to disconnect the AC
power cord from the PSU, before
starting the PSU BIST
