1|Page
Vehicle Communication Systems Comprehensive
Examination||Verified Exam!!!||, 2026/2027-Question
ASE/SAE-Aligned Automotive Electronics
Examination with Verified Answers||Newest Exam!!
Which of the following vehicles are equipped with the
Atlantis architecture? Select all that apply. - Answer-Jeep
renegade
Jeep compass
Alfa Giulia
Alfa Stelvio
what is the resistance of the terminating resistor on
networks equipped with one start connector? - Answer-60
ohms
with the bus active and no faults present, what voltages
should be measured on CAN-C(+)? - Answer-
approximately 3.2v
what Atlantis-high network uses splice block connectors? -
Answer-CAN-BH
,2|Page
with the bus active and no faults present, what voltages
should be measured on CAN-B(-)? - Answer-
approximately 0.4v
which resource should be used first for troubleshooting
DRB III Emulator concerns? - Answer-wiTECH knowledge
base
with the bus active and no faults present, what voltages
should be measured on LIN? - Answer-7.0v-10.0v
what electrical architecture requires the use of the mopar
diagnostic pod (MPD) for diagnostics? - Answer-Atlantis-
high
which of the following scan tool functions ate prevented if
a security gateway (SGW) becomes locked? select all that
apply. - Answer-start an actuator
run a system test
flash program a module
What vehicle architectures use an automatic process to
transfer ECU configuration? Select all that apply. - Answer-
PowerNet
, 3|Page
TIPM
What is the resistance of the terminating resistor on
networks equipped with one star connector? - Answer-60
ohms (Normal CAN Bus terminating resistance)
With the bus active and no faults present, what voltages
should be measured on CAN-C (-)? - Answer-Not
Approximately 4.8V
1.3-2.3V
with the bus active and no faults present, what voltages
should be measured on CAN-C(-)? - Answer-
approximately 1.8v
what Atlantis vehicles uses splice block connectors on
their CAN buses? select all that apply. - Answer-ga alfa
glulia
mp jeep compass
what are the key differences between CAN-FD and CAN-
C? select all that apply. - Answer-flexible bit rates
Vehicle Communication Systems Comprehensive
Examination||Verified Exam!!!||, 2026/2027-Question
ASE/SAE-Aligned Automotive Electronics
Examination with Verified Answers||Newest Exam!!
Which of the following vehicles are equipped with the
Atlantis architecture? Select all that apply. - Answer-Jeep
renegade
Jeep compass
Alfa Giulia
Alfa Stelvio
what is the resistance of the terminating resistor on
networks equipped with one start connector? - Answer-60
ohms
with the bus active and no faults present, what voltages
should be measured on CAN-C(+)? - Answer-
approximately 3.2v
what Atlantis-high network uses splice block connectors? -
Answer-CAN-BH
,2|Page
with the bus active and no faults present, what voltages
should be measured on CAN-B(-)? - Answer-
approximately 0.4v
which resource should be used first for troubleshooting
DRB III Emulator concerns? - Answer-wiTECH knowledge
base
with the bus active and no faults present, what voltages
should be measured on LIN? - Answer-7.0v-10.0v
what electrical architecture requires the use of the mopar
diagnostic pod (MPD) for diagnostics? - Answer-Atlantis-
high
which of the following scan tool functions ate prevented if
a security gateway (SGW) becomes locked? select all that
apply. - Answer-start an actuator
run a system test
flash program a module
What vehicle architectures use an automatic process to
transfer ECU configuration? Select all that apply. - Answer-
PowerNet
, 3|Page
TIPM
What is the resistance of the terminating resistor on
networks equipped with one star connector? - Answer-60
ohms (Normal CAN Bus terminating resistance)
With the bus active and no faults present, what voltages
should be measured on CAN-C (-)? - Answer-Not
Approximately 4.8V
1.3-2.3V
with the bus active and no faults present, what voltages
should be measured on CAN-C(-)? - Answer-
approximately 1.8v
what Atlantis vehicles uses splice block connectors on
their CAN buses? select all that apply. - Answer-ga alfa
glulia
mp jeep compass
what are the key differences between CAN-FD and CAN-
C? select all that apply. - Answer-flexible bit rates
