TEXAS STATE INSPECTOR SAFETY CERT. Updated most
Frequent Tested Exam 2026 WITH Recent Newest Verified
And Well Analyzed Exam Questions (Actual Exam 2026-
2027) Correct Detailed & Verified ANSWERS (100% Accurate
Solutions) ALREADY GRADED A+||NEWEST VERSION Of
The Exam Guarantee Pass!!
Brakes would be rejected if: -ANSWERS-There is obvious metal to metal contact when
brakes are applied.
When issuing a Vehicle Inspection Report to a vehicle, the VIN will be taken from the: -
ANSWERS-Vehicle
Proof of financial responsibility is not required on motor vehicles prior to the model year
1988. -ANSWERS-False
When is a vehicle required to be inspected for seat belts? -ANSWERS-Anchorages
were part of the manufactures original equipment
The turn signal selector switch must lock in the proper position when applied on: -
ANSWERS-All vehicles
A truck or trailer is required to have clearance lamps and side marker lamps if the total
width of the vehicle is: -ANSWERS-80 inches or more
In order to pass inspection, tires must have a tread depth of at least ___ in the two
center adjacent major grooves. -ANSWERS-2/32 inch
A parking brake is required to be inspected on all cars and trucks beginning with the
model year: -ANSWERS-1960
, A muffler with a hole which has been patched: -ANSWERS-Will be rejected
Fluid level in the brake master cylinder must not be more than how many inches below
the top of the reservoir? -ANSWERS-1 inch
One of the required procedures in the inspection of the steering is: -ANSWERS-Turning
the steering wheel from full left to full right
Conventional brakes or non-power brakes must have a minimum pedal reserve of: -
ANSWERS-2 inch
Any tire with wear bar indicators would be rejected for the following reason: -
ANSWERS-Tread wear indicators contact the road on any two adjacent major grooves
in the center of the middle of the tire
LED tail lamps may have no more than ______ of diodes malfunctioning to pass
inspection. -ANSWERS-50%
When performing a road test on the service brakes, a truck weighing over 10,000 lbs
GVW (this would include larger trucks but not truck-trailer combinations) should be
driven at a speed of 20 mph and should stop within: -ANSWERS-40 feet
The vehicle owner/operator should be present when the inspector is checking CNG tank
located in the trunk of the car. -ANSWERS-True
Glass coating or sun screening materials on windshield may not extend down past the
AS-1 line or more than ____ inches, whichever is closer to the top of the windshield: -
ANSWERS-5 inches
When using a window tint meter, the amount of light transmission cannot be less than? -
ANSWERS-25%
Frequent Tested Exam 2026 WITH Recent Newest Verified
And Well Analyzed Exam Questions (Actual Exam 2026-
2027) Correct Detailed & Verified ANSWERS (100% Accurate
Solutions) ALREADY GRADED A+||NEWEST VERSION Of
The Exam Guarantee Pass!!
Brakes would be rejected if: -ANSWERS-There is obvious metal to metal contact when
brakes are applied.
When issuing a Vehicle Inspection Report to a vehicle, the VIN will be taken from the: -
ANSWERS-Vehicle
Proof of financial responsibility is not required on motor vehicles prior to the model year
1988. -ANSWERS-False
When is a vehicle required to be inspected for seat belts? -ANSWERS-Anchorages
were part of the manufactures original equipment
The turn signal selector switch must lock in the proper position when applied on: -
ANSWERS-All vehicles
A truck or trailer is required to have clearance lamps and side marker lamps if the total
width of the vehicle is: -ANSWERS-80 inches or more
In order to pass inspection, tires must have a tread depth of at least ___ in the two
center adjacent major grooves. -ANSWERS-2/32 inch
A parking brake is required to be inspected on all cars and trucks beginning with the
model year: -ANSWERS-1960
, A muffler with a hole which has been patched: -ANSWERS-Will be rejected
Fluid level in the brake master cylinder must not be more than how many inches below
the top of the reservoir? -ANSWERS-1 inch
One of the required procedures in the inspection of the steering is: -ANSWERS-Turning
the steering wheel from full left to full right
Conventional brakes or non-power brakes must have a minimum pedal reserve of: -
ANSWERS-2 inch
Any tire with wear bar indicators would be rejected for the following reason: -
ANSWERS-Tread wear indicators contact the road on any two adjacent major grooves
in the center of the middle of the tire
LED tail lamps may have no more than ______ of diodes malfunctioning to pass
inspection. -ANSWERS-50%
When performing a road test on the service brakes, a truck weighing over 10,000 lbs
GVW (this would include larger trucks but not truck-trailer combinations) should be
driven at a speed of 20 mph and should stop within: -ANSWERS-40 feet
The vehicle owner/operator should be present when the inspector is checking CNG tank
located in the trunk of the car. -ANSWERS-True
Glass coating or sun screening materials on windshield may not extend down past the
AS-1 line or more than ____ inches, whichever is closer to the top of the windshield: -
ANSWERS-5 inches
When using a window tint meter, the amount of light transmission cannot be less than? -
ANSWERS-25%
