SOLIDWORKS CSWA-AM
CERTIFICATION SCRIPT 2026
QUESTIONS WITH SOLUTIONS
GRADED A+
◍ h-method of meshing involves.
Answer: increasing mesh density
◍ p-method of meshing involves.
Answer: increasing mesh element polynomial order
◍ is it possible to model breaking of glass on the floor using linear static
analysis?.
Answer: no
◍ FFF (fused filament fabrication).
Answer: A 3D printing method which lays down each layer of filament
◍ SLA (Stereolithography).
Answer: A rapid prototyping process that fabricates a part layer-wise by
hardening a photopolymer with a guided laser beam. Using an Ultraviolet
laser
◍ which of the following cases, the rope will most likely break?.
Answer: both are the same
◍ Assuming a linear static study, if the Young's modulus of the material is
doubles (everything else remains the same), then the tensile stress will be.
Answer: doubles
◍ iso lot in the simulation will enable to.
Answer: set lower and upper limits to see desired stress range
, ◍ SLS (Selective Laser Sintering).
Answer: A rapid prototyping process that used a moving laser beam to sinter
heat-fusible powders one layer at a time.
◍ Filament material FFF.
Answer: Polylactic Acid and Acrylonitrile-Butadiene-Styrene
◍ Polylactic Acid (PLA).
Answer: A thermoplastic formed using organic material.
◍ Acrylonitrile Butadiene Styrene (ABS).
Answer: Also known as ABS; a common thermoplastic used to make light,
rigid, molded nail tips.
◍ Nylon.
Answer: synthetic polymer, used in industrial applications
◍ which statement best describes a compatible mesh?.
Answer: a mesh where elements on touching bodies have overlaying nodes
◍ Polyvinyl alcohol (PVA).
Answer: A water-soluble synthetic thickener/adhesive.
◍ adhesive applicators.
Answer: blue painters tape, hair spray, glue stick
◍ maximum and minimum value indicators are displayed on stress and
displacement plots in SOLIDWORKS simulation for a linear static study.
Answer: true
◍ what SOLIDWORKS simulation tool should you use to determine the result
values at specific locations (nodes) in a model using SOLIDWORKS
simulation?.
Answer: probe tool
◍ SLS (Selective Laser Sintering).
Answer: preferred rapid prototyping method of metals and exotic materials
◍ what criteria are best suited to check the failure of ductile materials in
CERTIFICATION SCRIPT 2026
QUESTIONS WITH SOLUTIONS
GRADED A+
◍ h-method of meshing involves.
Answer: increasing mesh density
◍ p-method of meshing involves.
Answer: increasing mesh element polynomial order
◍ is it possible to model breaking of glass on the floor using linear static
analysis?.
Answer: no
◍ FFF (fused filament fabrication).
Answer: A 3D printing method which lays down each layer of filament
◍ SLA (Stereolithography).
Answer: A rapid prototyping process that fabricates a part layer-wise by
hardening a photopolymer with a guided laser beam. Using an Ultraviolet
laser
◍ which of the following cases, the rope will most likely break?.
Answer: both are the same
◍ Assuming a linear static study, if the Young's modulus of the material is
doubles (everything else remains the same), then the tensile stress will be.
Answer: doubles
◍ iso lot in the simulation will enable to.
Answer: set lower and upper limits to see desired stress range
, ◍ SLS (Selective Laser Sintering).
Answer: A rapid prototyping process that used a moving laser beam to sinter
heat-fusible powders one layer at a time.
◍ Filament material FFF.
Answer: Polylactic Acid and Acrylonitrile-Butadiene-Styrene
◍ Polylactic Acid (PLA).
Answer: A thermoplastic formed using organic material.
◍ Acrylonitrile Butadiene Styrene (ABS).
Answer: Also known as ABS; a common thermoplastic used to make light,
rigid, molded nail tips.
◍ Nylon.
Answer: synthetic polymer, used in industrial applications
◍ which statement best describes a compatible mesh?.
Answer: a mesh where elements on touching bodies have overlaying nodes
◍ Polyvinyl alcohol (PVA).
Answer: A water-soluble synthetic thickener/adhesive.
◍ adhesive applicators.
Answer: blue painters tape, hair spray, glue stick
◍ maximum and minimum value indicators are displayed on stress and
displacement plots in SOLIDWORKS simulation for a linear static study.
Answer: true
◍ what SOLIDWORKS simulation tool should you use to determine the result
values at specific locations (nodes) in a model using SOLIDWORKS
simulation?.
Answer: probe tool
◍ SLS (Selective Laser Sintering).
Answer: preferred rapid prototyping method of metals and exotic materials
◍ what criteria are best suited to check the failure of ductile materials in
