1|Page
AMPP_NACE Coating Inspector Program Level 2
Exam (CIP Level 2)|| Verified Questions with Correct
Answers and explanations LATEST THIS YEAR -JUST
RELEASED.pdf 1|| NEWEST EXAM!!!
Individuals conducting Coating Surveys should:
a) Always be NACE Level 3 Certified Inspectors
b) Always be NACE or SSPC Protective coating
Specialists
c) Always be experienced Specification Writers
d) Always be trained and experienced in the Coating
Industry - Answer-d) Always be trained and experienced in
the Coating Industry
The cost of qualified Coating Inspection is normally offset
by:
a) Lower Application Costs
b) Lower Coating Life Cycle Costs
c) Lower Safety Enforcement Costs
d) Lower Supervision Costs - Answer-b) Lower Coating
Life Cycle Costs
,2|Page
You are a NACE Level 2 Coating Inspector who has just
arrived on a job in progress where there is no inspection
and Test Plan (ITP). The first morning you arrive the job is
behind schedule, and you are asked to take DIY Film
Thickness readings.
Your FIRST preferred course of action is to:
a) Refuse to take readings until an is in place
b) Develop your own methodology and proceed take the
readings
c) Use a generally accepted industry standard and to take
readings
d) Call your supervisor - Answer-c) Use a generally
accepted industry standard and to take readings
When conducting inspections, the Inspector should follow
which standards:
a) NACE and SSPC standards in North America
b) ISO standards in Europe and Asia
c) Australian standards in Australia
d) The specified standards - Answer-d) The specified
standards
,3|Page
You are the NACE Level 2 Coating Inspector where SSPC
PA 2 has been specified with an additional requirement
that no individual gauge reading shall be below a certain
value. As this is not part of the standard you should:
a) Ignore the additional requirement
b) Enforce the additional requirement
c) Call your supervisor
d) Request clarification from the specifier - Answer-b)
Enforce the additional requirement
The coating applicator has ignored a enface preparation
hold point and applied coating over the surface without a
sign off from you as the inspector.
Your FIRST preferred course of action is to:
a) Stop the job
b) Require the Applicator to remove the coating
c) Advise the Owner and write a Non-Conformance report
d) Ignore the situation - Answer-b) Require the Applicator
to remove the coating
In the event of a conflict between the Product Data Sheet
and the Specification:
, 4|Page
a) The Product Data Sheet prevails
b) The Specification prevails
c) It is up to the Inspector to decide which one to follow
d) It is up to the Applicator to decide which one to follow -
Answer-b) The Specification prevails
From a corrosion perspective, the main difference
between Ferrous and Non-Ferrous Metals is:
a) Cost
b) Iron content
c) Appearance
d) Safety - Answer-b) Iron content
You are the NACE Coating Inspector on a tank lining
project and are asked to perform a high voltage holiday
test after the coating applicators have completed their final
repairs. After meeting all the confined space entry permit
you enter the tank and notice a very strong odor of solvent
Your first course of action should to:
a) Investigate to find the source of the odor
b) Don your air supplied respirator and continue the
testing
AMPP_NACE Coating Inspector Program Level 2
Exam (CIP Level 2)|| Verified Questions with Correct
Answers and explanations LATEST THIS YEAR -JUST
RELEASED.pdf 1|| NEWEST EXAM!!!
Individuals conducting Coating Surveys should:
a) Always be NACE Level 3 Certified Inspectors
b) Always be NACE or SSPC Protective coating
Specialists
c) Always be experienced Specification Writers
d) Always be trained and experienced in the Coating
Industry - Answer-d) Always be trained and experienced in
the Coating Industry
The cost of qualified Coating Inspection is normally offset
by:
a) Lower Application Costs
b) Lower Coating Life Cycle Costs
c) Lower Safety Enforcement Costs
d) Lower Supervision Costs - Answer-b) Lower Coating
Life Cycle Costs
,2|Page
You are a NACE Level 2 Coating Inspector who has just
arrived on a job in progress where there is no inspection
and Test Plan (ITP). The first morning you arrive the job is
behind schedule, and you are asked to take DIY Film
Thickness readings.
Your FIRST preferred course of action is to:
a) Refuse to take readings until an is in place
b) Develop your own methodology and proceed take the
readings
c) Use a generally accepted industry standard and to take
readings
d) Call your supervisor - Answer-c) Use a generally
accepted industry standard and to take readings
When conducting inspections, the Inspector should follow
which standards:
a) NACE and SSPC standards in North America
b) ISO standards in Europe and Asia
c) Australian standards in Australia
d) The specified standards - Answer-d) The specified
standards
,3|Page
You are the NACE Level 2 Coating Inspector where SSPC
PA 2 has been specified with an additional requirement
that no individual gauge reading shall be below a certain
value. As this is not part of the standard you should:
a) Ignore the additional requirement
b) Enforce the additional requirement
c) Call your supervisor
d) Request clarification from the specifier - Answer-b)
Enforce the additional requirement
The coating applicator has ignored a enface preparation
hold point and applied coating over the surface without a
sign off from you as the inspector.
Your FIRST preferred course of action is to:
a) Stop the job
b) Require the Applicator to remove the coating
c) Advise the Owner and write a Non-Conformance report
d) Ignore the situation - Answer-b) Require the Applicator
to remove the coating
In the event of a conflict between the Product Data Sheet
and the Specification:
, 4|Page
a) The Product Data Sheet prevails
b) The Specification prevails
c) It is up to the Inspector to decide which one to follow
d) It is up to the Applicator to decide which one to follow -
Answer-b) The Specification prevails
From a corrosion perspective, the main difference
between Ferrous and Non-Ferrous Metals is:
a) Cost
b) Iron content
c) Appearance
d) Safety - Answer-b) Iron content
You are the NACE Coating Inspector on a tank lining
project and are asked to perform a high voltage holiday
test after the coating applicators have completed their final
repairs. After meeting all the confined space entry permit
you enter the tank and notice a very strong odor of solvent
Your first course of action should to:
a) Investigate to find the source of the odor
b) Don your air supplied respirator and continue the
testing
