MICHIGAN STATE BRAKES CERTIFICATION
EXAM QUESTIONS WITH 100% VERIFIED
ANSWERS
\.Most 1995 & newer vehicles use which of the following types of wheels bearings
on non-drive wheel? - ANSWERS✔-Sealed non-serviceable
\.to test a vacuum power brake booster in the vehicle, you should pump the brake
pedal at least 4 times, hold the brake pedal depressed, and start the engine. the
brake pedal should: - ANSWERS✔-drop slightly and remain firm
\.You are installing a set of brake shoe linings that are not the same length.
Traditionally, the primary shoe lining is: - ANSWERS✔-Smaller and goes towards
the front of the car.
\.A cracked or torn vacuum diaphragm in a brake power booster would most likely
cause: - ANSWERS✔-a hard pedal feel requiring very high pedal effort to stop
\.A mechanic finds gear lube inside both rear brake drums on a rear wheel drive
vehicle. What is the most likely cause of this problem? - ANSWERS✔-A plugged
axle
, \.Which of the following incorrect service procedures will cause brake lock-up? -
ANSWERS✔-master cylinder push rod adjusted too long
\.Which of the following describes the proper way to depressurized an ABS
system? - ANSWERS✔-Pump the brake pedal at least 25 times (or more,
depending on the manufacturer's recommendation) with the ignition off.
\.The rear brakes are dragging after having new linings installed and the drums
machined. the most likely cause is the: - ANSWERS✔-technician use the parking
brake to adjust shoes and the cable is stuck
\.When turning brake drums: - ANSWERS✔-use a dampening strap to reduce
chatter
\.Which of the following is NOT a necessary drum brake measurement? -
ANSWERS✔-run-out
\.On a 3-channel system, which wheels are on the same circuit? - ANSWERS✔-
both rear wheels
\.One way to test an ABS wheel speed signal is to use _____ on your digital
multimeter. - ANSWERS✔-AC volts
\.The key input for the ABS control module comes from the: - ANSWERS✔-wheel
speed sensors
EXAM QUESTIONS WITH 100% VERIFIED
ANSWERS
\.Most 1995 & newer vehicles use which of the following types of wheels bearings
on non-drive wheel? - ANSWERS✔-Sealed non-serviceable
\.to test a vacuum power brake booster in the vehicle, you should pump the brake
pedal at least 4 times, hold the brake pedal depressed, and start the engine. the
brake pedal should: - ANSWERS✔-drop slightly and remain firm
\.You are installing a set of brake shoe linings that are not the same length.
Traditionally, the primary shoe lining is: - ANSWERS✔-Smaller and goes towards
the front of the car.
\.A cracked or torn vacuum diaphragm in a brake power booster would most likely
cause: - ANSWERS✔-a hard pedal feel requiring very high pedal effort to stop
\.A mechanic finds gear lube inside both rear brake drums on a rear wheel drive
vehicle. What is the most likely cause of this problem? - ANSWERS✔-A plugged
axle
, \.Which of the following incorrect service procedures will cause brake lock-up? -
ANSWERS✔-master cylinder push rod adjusted too long
\.Which of the following describes the proper way to depressurized an ABS
system? - ANSWERS✔-Pump the brake pedal at least 25 times (or more,
depending on the manufacturer's recommendation) with the ignition off.
\.The rear brakes are dragging after having new linings installed and the drums
machined. the most likely cause is the: - ANSWERS✔-technician use the parking
brake to adjust shoes and the cable is stuck
\.When turning brake drums: - ANSWERS✔-use a dampening strap to reduce
chatter
\.Which of the following is NOT a necessary drum brake measurement? -
ANSWERS✔-run-out
\.On a 3-channel system, which wheels are on the same circuit? - ANSWERS✔-
both rear wheels
\.One way to test an ABS wheel speed signal is to use _____ on your digital
multimeter. - ANSWERS✔-AC volts
\.The key input for the ABS control module comes from the: - ANSWERS✔-wheel
speed sensors
