1|Page
Arizona (AZ) CR8 Floor Covering Exam ACTUAL
VERIFIED EXAM COMPLETE QUESTIONS AND
CORRECT ANSWERS LATEST UPDATE THIS
YEAR||NEWEST EXAM!!!
What is the most important consideration in the production
of a professional looking tile job? - Answer-Performance of
a layout
The ideal tool for cutting parquet is? - Answer-Band saw
Before gluing flooring to a sub-floor the difference in
moisture content between the flooring and the sub-floor
should not be more than: - Answer-4%
What grade of maple (marble?) has a mixture of colors
and some defects? - Answer-Second grade
If not sealed properly, quarry tile can be permanently
damaged by: - Answer-Grout
What should you do to increase adhesion on large tiles? -
Answer-Comb in one direction only
,2|Page
What is Saltillo tile not good for? - Answer-Counter tops
What would happen if you applied thinset with a small
notched trowel on large tile? - Answer-Not enough thinset
Before nailing wood flooring down on plywood sub-floor,
what do you put down? - Answer-15lb felt paper
What nails do you use to fasten a loose subfloor with
1&1/4 inch thickness? - Answer-16d
A carpenter is installing a decorative baseboard trim that
will be stained. According to carpentry and building
construction, what type of joint should be used for a 90°
inside corner when the installer is using the best method
for quality construction? - Answer-Coped
Semi-vitreous tile that is to be grouted with portland
cement grout should first be: - Answer-Misted
Ceramic tile is to be installed using the "one coat" method
over gypsum board on wood studs; the "Tile Council of
America" recommends that the membrane be: - Answer-
15 pound roofing felt or 4 mil polyethylene
,3|Page
What is "non-resilient" flooring? - Answer-Flooring that has
surfaces with no give
The marble institute of America has classified marble and
stone into how many groups? - Answer-4 groups
When blind nailing 6ft plank flooring, how many nails are
used per plank? - Answer-10
The maximum allowable spacing when using 8d nails to
fasten the edges of 5/8 inch thick plywood to floor joists is
how many inches on the center? - Answer-6 inches
When applying plywood sub-flooring the minimum spacing
between adjacent panels at the edge is? - Answer-1/8 inch
on ends and edges
What is the perfect PH level for concrete when gluing
down carpet? - Answer-7-9
, 4|Page
What could cause stone tile to wear? - Answer-Tile set
with water base thin-set
What tool is used to shape or alter the edges of a stone
tile? - Answer-Round shaping stone
What is the maximum temperature for radiant heated
floors before installing carpet? - Answer-85° Fahrenheit
What is the minimum time to read a calcium chloride test
before installing carpet? - Answer-24 hours
What type of roller is used with VCT tile? - Answer-
Linoleum roller
The minimum exterior expansion joint width for joints 12
foot on center is: - Answer-3/8 inch
A 3-4-5 system is used to: - Answer-Check for square
Which of the following is the best type of saw to use when
cutting natural stone? - Answer-Wet saw
Arizona (AZ) CR8 Floor Covering Exam ACTUAL
VERIFIED EXAM COMPLETE QUESTIONS AND
CORRECT ANSWERS LATEST UPDATE THIS
YEAR||NEWEST EXAM!!!
What is the most important consideration in the production
of a professional looking tile job? - Answer-Performance of
a layout
The ideal tool for cutting parquet is? - Answer-Band saw
Before gluing flooring to a sub-floor the difference in
moisture content between the flooring and the sub-floor
should not be more than: - Answer-4%
What grade of maple (marble?) has a mixture of colors
and some defects? - Answer-Second grade
If not sealed properly, quarry tile can be permanently
damaged by: - Answer-Grout
What should you do to increase adhesion on large tiles? -
Answer-Comb in one direction only
,2|Page
What is Saltillo tile not good for? - Answer-Counter tops
What would happen if you applied thinset with a small
notched trowel on large tile? - Answer-Not enough thinset
Before nailing wood flooring down on plywood sub-floor,
what do you put down? - Answer-15lb felt paper
What nails do you use to fasten a loose subfloor with
1&1/4 inch thickness? - Answer-16d
A carpenter is installing a decorative baseboard trim that
will be stained. According to carpentry and building
construction, what type of joint should be used for a 90°
inside corner when the installer is using the best method
for quality construction? - Answer-Coped
Semi-vitreous tile that is to be grouted with portland
cement grout should first be: - Answer-Misted
Ceramic tile is to be installed using the "one coat" method
over gypsum board on wood studs; the "Tile Council of
America" recommends that the membrane be: - Answer-
15 pound roofing felt or 4 mil polyethylene
,3|Page
What is "non-resilient" flooring? - Answer-Flooring that has
surfaces with no give
The marble institute of America has classified marble and
stone into how many groups? - Answer-4 groups
When blind nailing 6ft plank flooring, how many nails are
used per plank? - Answer-10
The maximum allowable spacing when using 8d nails to
fasten the edges of 5/8 inch thick plywood to floor joists is
how many inches on the center? - Answer-6 inches
When applying plywood sub-flooring the minimum spacing
between adjacent panels at the edge is? - Answer-1/8 inch
on ends and edges
What is the perfect PH level for concrete when gluing
down carpet? - Answer-7-9
, 4|Page
What could cause stone tile to wear? - Answer-Tile set
with water base thin-set
What tool is used to shape or alter the edges of a stone
tile? - Answer-Round shaping stone
What is the maximum temperature for radiant heated
floors before installing carpet? - Answer-85° Fahrenheit
What is the minimum time to read a calcium chloride test
before installing carpet? - Answer-24 hours
What type of roller is used with VCT tile? - Answer-
Linoleum roller
The minimum exterior expansion joint width for joints 12
foot on center is: - Answer-3/8 inch
A 3-4-5 system is used to: - Answer-Check for square
Which of the following is the best type of saw to use when
cutting natural stone? - Answer-Wet saw
