ammo cdc eoc 2Exam questions and answers Graded
A+| 2026 Updated
Before using an electric drill, what is the first thing you should do?
Make sure the diameter of the hole to be drilled is within the capacity of the drill
The purpose of cutting lubricant in most drilling operations is to increase the
drilling speed and the drill bit life.
Which minimum articles of safety gear must be worn when using a bench
grinder?
Eye and face protection
An electric saw blade must be operating at what speed before it contacts the
material being cut?
Full
How many pounds per square inch (psi) of clean, dry air is required at the tool
end of the air hose to ensure the tool is operating safely and efficiently?
90
What condition would prevent an operator from applying power to a hoist or
other powered lifting device?
An Air Force (AF) Form 979 is attached to the unit.
What should be worn anytime there is a potential for injury from overhead
objects during a lifting operation?
Protective helmets
What is the most common type of lifting sling used in the munitions career field?
Wire rope
The following are all good safety practices to follow when using a lifting sling
except
,inspecting the sling by passing your bare hand over the body of the sling.
The annunciators displayed on the Fluke 8025-series multimeter are used to
distinguish among
ohms, kilohms, and megohms.
What are the two operational modes of the Fluke 8025-series multimeter?
Range and hold
The steering system on the MHU-141/M trailer has a turning radius of how many
degrees?
40
When the MHU-141 trailer is loaded or towed with the hinged deck panels open,
what must be done?
The deck-panel supports must be properly positioned and locked in place with
quick-release pins
What is the maximum load capacity of the MHU-110/M trailer?
15,000 pounds
he parking brake on the MHU-110/M is applied by
pulling either one of two hand levers located on each side of the front of the
trailer.
How many openings (hinged door panels) are on the deck of the MHU-226 trailer?
Three
What type of steering aids the MHU-226 in a tighter steering radius?
Four-wheel double Ackerman
After 463L pallets are positioned on a rollerized trailer, what can you use to
secure the pallets to the trailer?
MB-1 chain assemblies and/or tie-down straps
What kind of movement supports on-base activities to or from the flightline?
, Operational
What munitions item is not loaded into transport modules by munitions
personnel?
20 MM
What transport module used for chaff/flare munitions has a maximum capacity of
40 magazines?
ALE-40
How often should the positive locking devices on the doors of munitions transport
modules be checked?
After loading, unloading, and periodically between stops
The purpose of the transport beam beneath the lift arm assemblies on the MJ-1-
series lift truck is to
provide added support and to relieve hydraulic pressure from the lift arms when
carrying loads for long distances.
What is the lifting capacity of the MJ-1 series lift truck?
3,000 pounds
What is the lifting capacity of the MHU-83-series lift truck?
7,000 pounds
When using the MHU-83-series lift truck with fork adapters, you immediately
reduce its lifting capability by 1,000 pounds.
What happens when you release the accelerator pedal on a vehicle driven with a
hydrostatic transmission?
The unit coasts to a stop very quickly
What is the primary drawback to using the hydraulic hand pump to build
hydraulic pressure on the MHU-83-series lift truck?
Extremely slow way to build hydraulic pressure
A+| 2026 Updated
Before using an electric drill, what is the first thing you should do?
Make sure the diameter of the hole to be drilled is within the capacity of the drill
The purpose of cutting lubricant in most drilling operations is to increase the
drilling speed and the drill bit life.
Which minimum articles of safety gear must be worn when using a bench
grinder?
Eye and face protection
An electric saw blade must be operating at what speed before it contacts the
material being cut?
Full
How many pounds per square inch (psi) of clean, dry air is required at the tool
end of the air hose to ensure the tool is operating safely and efficiently?
90
What condition would prevent an operator from applying power to a hoist or
other powered lifting device?
An Air Force (AF) Form 979 is attached to the unit.
What should be worn anytime there is a potential for injury from overhead
objects during a lifting operation?
Protective helmets
What is the most common type of lifting sling used in the munitions career field?
Wire rope
The following are all good safety practices to follow when using a lifting sling
except
,inspecting the sling by passing your bare hand over the body of the sling.
The annunciators displayed on the Fluke 8025-series multimeter are used to
distinguish among
ohms, kilohms, and megohms.
What are the two operational modes of the Fluke 8025-series multimeter?
Range and hold
The steering system on the MHU-141/M trailer has a turning radius of how many
degrees?
40
When the MHU-141 trailer is loaded or towed with the hinged deck panels open,
what must be done?
The deck-panel supports must be properly positioned and locked in place with
quick-release pins
What is the maximum load capacity of the MHU-110/M trailer?
15,000 pounds
he parking brake on the MHU-110/M is applied by
pulling either one of two hand levers located on each side of the front of the
trailer.
How many openings (hinged door panels) are on the deck of the MHU-226 trailer?
Three
What type of steering aids the MHU-226 in a tighter steering radius?
Four-wheel double Ackerman
After 463L pallets are positioned on a rollerized trailer, what can you use to
secure the pallets to the trailer?
MB-1 chain assemblies and/or tie-down straps
What kind of movement supports on-base activities to or from the flightline?
, Operational
What munitions item is not loaded into transport modules by munitions
personnel?
20 MM
What transport module used for chaff/flare munitions has a maximum capacity of
40 magazines?
ALE-40
How often should the positive locking devices on the doors of munitions transport
modules be checked?
After loading, unloading, and periodically between stops
The purpose of the transport beam beneath the lift arm assemblies on the MJ-1-
series lift truck is to
provide added support and to relieve hydraulic pressure from the lift arms when
carrying loads for long distances.
What is the lifting capacity of the MJ-1 series lift truck?
3,000 pounds
What is the lifting capacity of the MHU-83-series lift truck?
7,000 pounds
When using the MHU-83-series lift truck with fork adapters, you immediately
reduce its lifting capability by 1,000 pounds.
What happens when you release the accelerator pedal on a vehicle driven with a
hydrostatic transmission?
The unit coasts to a stop very quickly
What is the primary drawback to using the hydraulic hand pump to build
hydraulic pressure on the MHU-83-series lift truck?
Extremely slow way to build hydraulic pressure
