At what stage of the construction process would the builder cut out the sole plate in a door
opening? - ANSWER after the wall has been erected and braced
When wide square edge boards are being used for board and batten siding, how should the
batten strips be nailed ? - ANSWER to only one siding board
According to the code, the minimum allowable height of a guardrail at a restaurant deck (or
any commercial building) is _____ inches above the finished floor height of the deck or bal-
cony. - ANSWER 42
If the blueprint does not disclose an exterior doors rough opening, then the standard prac-
tice would be to frame the width _____ oversize. - ANSWER 2 inches
How are resilient channels used in drywall application? - ANSWER to decrease sound
transmission in walls and partitions
What screws are used to attach steel studs to the top and bottom steel track? - ANSWER
pan head, type S. It attaches stud to runner up to 14-ga
In single family dwelling sleeping rooms, the minimum net clear opening width of windows,
which are required for emergency egress or rescue, is _____ inches. - ANSWER 20
According to the code what is the minimum slope on which asphalt strip shingles may be in-
stalled? - ANSWER 2:12
1
,According to Code the MAXIMUM diameter of a hole that may be bored in a 2 by 10 joist is
_____ inches. - ANSWER 3
According to the Code, notches allowed in the top or bottom of joists shall not exceed what
fraction of the depth of the joist? - ANSWER 1/6
While trenching and excavating, OSHA requires at least _____ feet of clear unobstructed dis-
tance from the trenches edge to the toe or edge of the dirt or spoils pile. - ANSWER 2
feet
What is the actual size of a 2 x 4 surfaced dry piece of framing lumber? - ANSWER 1-1/2
by 3-1/2
What is the minimum height of a guardrail on a residential deck ? - ANSWER 36 inches
A minimum tread run for stairways (other than spiral stairs) in single family dwellings having
an occupant load of less than 10 is _____ inches. - ANSWER 10
Dampening of the subgrade or the wood concrete forms prior to the placement of concrete
will: - ANSWER prevent rapid extraction of the mixing water from the concrete
Notches on the ends of joists shall not exceed _____ percent of the joist depth. - AN-
SWER 25 (1/4th)
According to code, asphalt shingles installed on roof with a slope of 4:12 or greater require
an underlayment of: - ANSWER one layer #15 non-perforated felt
How much clearance is the wood framing required to have where a masonry chimney passes
through the roof opening? - ANSWER 2 inches
2
, Asphalt shingles installed in warmer climates with a slope of 4 in 12 or more should have a
minimum underlayment of: - ANSWER 1 layer of # 15
When should concrete curing procedures start? - ANSWER As soon as possible after fin-
ishing.
A kind of molding installed on the vertical wall used to accept aluminum soffit panels is: -
ANSWER "F" Channel
A concrete slab should be bull floated as soon as possible after: - ANSWER screeding
According to OSHA, powered concrete trowels that are manually guided shall be equipped
with: - ANSWER a hand release shut off switch
When workers are required to enter a trench, shoring is required if the trench is what mini-
mum depth? - ANSWER 5 feet
The minimum distance that end joints shall be offset in double top plates is _____ inches. -
ANSWER 24
The minimum overlap of vertical joints of felt or paper, which is applied to exterior walls, as
a weather resistant barrier, is _____ inches. - ANSWER Not less than 6
How do you calculate cubic yards ? - ANSWER LxWxH=
then divide by 27 = Cubic Yards
What size screw should be used to attach steel sheathing to a metal structure? - ANSWER
Self tapping #8
3
opening? - ANSWER after the wall has been erected and braced
When wide square edge boards are being used for board and batten siding, how should the
batten strips be nailed ? - ANSWER to only one siding board
According to the code, the minimum allowable height of a guardrail at a restaurant deck (or
any commercial building) is _____ inches above the finished floor height of the deck or bal-
cony. - ANSWER 42
If the blueprint does not disclose an exterior doors rough opening, then the standard prac-
tice would be to frame the width _____ oversize. - ANSWER 2 inches
How are resilient channels used in drywall application? - ANSWER to decrease sound
transmission in walls and partitions
What screws are used to attach steel studs to the top and bottom steel track? - ANSWER
pan head, type S. It attaches stud to runner up to 14-ga
In single family dwelling sleeping rooms, the minimum net clear opening width of windows,
which are required for emergency egress or rescue, is _____ inches. - ANSWER 20
According to the code what is the minimum slope on which asphalt strip shingles may be in-
stalled? - ANSWER 2:12
1
,According to Code the MAXIMUM diameter of a hole that may be bored in a 2 by 10 joist is
_____ inches. - ANSWER 3
According to the Code, notches allowed in the top or bottom of joists shall not exceed what
fraction of the depth of the joist? - ANSWER 1/6
While trenching and excavating, OSHA requires at least _____ feet of clear unobstructed dis-
tance from the trenches edge to the toe or edge of the dirt or spoils pile. - ANSWER 2
feet
What is the actual size of a 2 x 4 surfaced dry piece of framing lumber? - ANSWER 1-1/2
by 3-1/2
What is the minimum height of a guardrail on a residential deck ? - ANSWER 36 inches
A minimum tread run for stairways (other than spiral stairs) in single family dwellings having
an occupant load of less than 10 is _____ inches. - ANSWER 10
Dampening of the subgrade or the wood concrete forms prior to the placement of concrete
will: - ANSWER prevent rapid extraction of the mixing water from the concrete
Notches on the ends of joists shall not exceed _____ percent of the joist depth. - AN-
SWER 25 (1/4th)
According to code, asphalt shingles installed on roof with a slope of 4:12 or greater require
an underlayment of: - ANSWER one layer #15 non-perforated felt
How much clearance is the wood framing required to have where a masonry chimney passes
through the roof opening? - ANSWER 2 inches
2
, Asphalt shingles installed in warmer climates with a slope of 4 in 12 or more should have a
minimum underlayment of: - ANSWER 1 layer of # 15
When should concrete curing procedures start? - ANSWER As soon as possible after fin-
ishing.
A kind of molding installed on the vertical wall used to accept aluminum soffit panels is: -
ANSWER "F" Channel
A concrete slab should be bull floated as soon as possible after: - ANSWER screeding
According to OSHA, powered concrete trowels that are manually guided shall be equipped
with: - ANSWER a hand release shut off switch
When workers are required to enter a trench, shoring is required if the trench is what mini-
mum depth? - ANSWER 5 feet
The minimum distance that end joints shall be offset in double top plates is _____ inches. -
ANSWER 24
The minimum overlap of vertical joints of felt or paper, which is applied to exterior walls, as
a weather resistant barrier, is _____ inches. - ANSWER Not less than 6
How do you calculate cubic yards ? - ANSWER LxWxH=
then divide by 27 = Cubic Yards
What size screw should be used to attach steel sheathing to a metal structure? - ANSWER
Self tapping #8
3
