• Wrong document? Swap it for free
  • Written by students who passed
  • Immediately available after payment
  • Read online or as PDF
Sell
Where do you study
Your language
Document preview thumbnail
Preview 3 out of 29 pages
Exam (elaborations)

Inspector Certification Study Guide and Practice Questions

Document preview thumbnail
Preview 3 out of 29 pages

This document covers essential topics for Inspector Certification, including inspection procedures, safety standards, regulatory compliance, reporting practices, and quality control. It provides structured summaries and practice questions to help reinforce understanding and prepare effectively for certification exams. The material is aligned with professional standards for inspectors across multiple industries.

Content preview

Inspector Certification Study Guide and Practice Questions


1.You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is
being applied. After application of the 19 coat you notice small blisters in some areas of the
applied lining. Your FIRST preferred course of action is to:



A. Break the blisters to see what's inside

B. Document the problem and advise the Contractor and Owner's representative

C. Document the problem and advise the Contractor D. Extract any liquid that may be inside the
blister and send it to the lab for further analysis - correct answer ✔✔ B



2.Dew point is the temperature at which



A. water freezes.

B. humidity decreases

C. condensation occurs.

D. the air is saturated. - correct answer ✔✔ C



3.If a contractor is using a poorly maintained compressor to supply air for abrasive blast
cleaning and conventional airspray, the coating inspector should perform a



A. dry film thickness (DEI) measurement.

B. wet film thickness (WFT) measurement.

C. blotter test for the presence of oil and water.

D. vial lest. - correct answer ✔✔ C



4.Upon arrival of coating materials, the inspector should

,A. review coating contractors' plans for storage of coating materials and confirm they meet
national, local and owners' fire and environmental regulations.

B. observe and document the amount of material and batch numbers.

C. observe aryl document that the applicator WFT at regular intervals during application.

D. observe and document time frame and environmental conditions between each coat. -
correct answer ✔✔ B



5.Relative humidity is



A. a measure of the amount of moisture in the air compared to saturation level.

B. a measure of the amount of moisture in the air compared to the air temperature.

C. the lowest temperature at which moisture forms on a steel surface.

D. the highest temperature at which moisture forms on a steel surface. - correct answer ✔✔ A



6.Galvanic corrosion occurs on which of the following substrates:



A. Concrete

B. Fiberglass Reinforced Plastic

C. Metal

D. Wood - correct answer ✔✔ C



7.When applying Thermal Spray Coatings the specification is most likely to refence:



A. SSPC PA 2

B. NACE SP 0178

C. NACE SP 0188

, D. SSPC-CS 23.00/AWS C2.23/NACE No. 12 - correct answer ✔✔ D



8.What is the minimum recommended distance away from an edge that an inspector should
take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?



A. 1 cm (.39 inch)

B. 2.5 cm (1 inch)

C. 6.35 cm (2.5 inch)

D. 2.5 millimeters (.10 inch) - correct answer ✔✔ B



9.Polymerization is the process of:



A. Monomers telegraphing

B. Monomers joining together

C. All thermoplastic coatings

D. All organic coatings - correct answer ✔✔ B



10.An exposed area of the substrate or previous coat of a conductive coating material, often
caused by poor application technique is called



A. cracking.

B. sagging.

C. holiday.

D. checking. - correct answer ✔✔ C



11.Checking is

Document information

Uploaded on
March 26, 2026
Number of pages
29
Written in
2025/2026
Type
Exam (elaborations)
Contains
Questions & answers
$28.49

Wrong document? Swap it for free Within 14 days of purchase and before downloading, you can choose a different document. You can simply spend the amount again.
Written by students who passed
Immediately available after payment
Read online or as PDF

Seller avatar
Reputation scores are based on the amount of documents a seller has sold for a fee and the reviews they have received for those documents. There are three levels: Bronze, Silver and Gold. The better the reputation, the more your can rely on the quality of the sellers work.
7Eleven
4.0
(123)
Sold
330
Followers
209
Items
18529
Last sold
4 days ago



Why students choose Stuvia

Created by fellow students, verified by reviews

Quality you can trust: written by students who passed their tests and reviewed by others who've used these notes.

Didn't get what you expected? Choose another document

No worries! You can instantly pick a different document that better fits what you're looking for.

Pay as you like, start learning right away

No subscription, no commitments. Pay the way you're used to via credit card and download your PDF document instantly.

Student with book image

“Bought, downloaded, and aced it. It really can be that simple.”

Alisha Student

Working on your references?

Create accurate citations in APA, MLA and Harvard with our free citation generator.

Working on your references?

Frequently asked questions