Michigan State Brakes Certification Actual Exam And
Practice Newest 2026-2027 With Complete Questions
And Correct Detailed Answers| Brand New Version!
Tech A bench bleeds the master cylinder before installing it on the car.
Tech B depresses the pistons and allows gravity to push air out of the
master cylinder before connecting the brake lines to the master
cylinder. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-B
Tech A bench bleeds the master cylinder installing it on the car. Tech B
depresses the pistons and allows gravity to push air out of the master
cylinder before connecting the brake lines to the master cylinder. Who
is right?
A. A only
B. B only
C. A and B
1|Page
,D. Neither - ANSWER-A
Which of the following is the LAST likely cause of one brake dragging?
A. A clogged hydraulic port, brake line, or hose
B. A stuck parking brake cable
C. A corroded master cylinder bore
D. A stuck brake caliper piston - ANSWER-C
A car has a spongy pedal. Which of the following could be the cause?
A. Air in the system
B. An internal master cylinder leak
C. Worn brake pads
D. Warped brake disc - ANSWER-A
Tech A says a stuck caliper can cause the car to pull during braking. Tech
B says a broken return spring in a rear drum brake can cause the car to
pull during braking. Who is right?
A. A only
B. B only
2|Page
,C. A and B
D. Neither - ANSWER-C
Which of the following is not correct in the procedure for preparing a
brake rotor for machining?
A. Use a micrometer to check for thickness variations
B. Use a micrometer to check the thickness of the rotor
C. Use a brake micrometer to measure the diameter
D. Use a micrometer to measure parallelism - ANSWER-C
A car equipped with a vacuum assist power brake system needs an
abnormal amount of pedal effort to stop the car, which of the following
could be the cause?
A. An internal master cylinder leak
B. Too much vacuum is applied to the booster
C. A plugged booster air breather
D. Low fluid level - ANSWER-C
While diagnosing a braking problem on a car equipped with a vacuum
power booster: Tech A says excessive pedal travel can because by a
3|Page
, leaking brake valve. Tech B says excessive pedal travel can be caused by
an improperly adjusted master cylinder push rod. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-B
Tech A uses a silencer belt only on the brake rotors that have heavy heat
checks while machining them. Tech B always machines a brake rotor to
the minimum thickness allowed. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-D
The brakes of a car chatter when they are applied, which of the
following could cause this problem?
A. A loose metering valve
B. insufficient clearance between the rotor and brake pads
4|Page
Practice Newest 2026-2027 With Complete Questions
And Correct Detailed Answers| Brand New Version!
Tech A bench bleeds the master cylinder before installing it on the car.
Tech B depresses the pistons and allows gravity to push air out of the
master cylinder before connecting the brake lines to the master
cylinder. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-B
Tech A bench bleeds the master cylinder installing it on the car. Tech B
depresses the pistons and allows gravity to push air out of the master
cylinder before connecting the brake lines to the master cylinder. Who
is right?
A. A only
B. B only
C. A and B
1|Page
,D. Neither - ANSWER-A
Which of the following is the LAST likely cause of one brake dragging?
A. A clogged hydraulic port, brake line, or hose
B. A stuck parking brake cable
C. A corroded master cylinder bore
D. A stuck brake caliper piston - ANSWER-C
A car has a spongy pedal. Which of the following could be the cause?
A. Air in the system
B. An internal master cylinder leak
C. Worn brake pads
D. Warped brake disc - ANSWER-A
Tech A says a stuck caliper can cause the car to pull during braking. Tech
B says a broken return spring in a rear drum brake can cause the car to
pull during braking. Who is right?
A. A only
B. B only
2|Page
,C. A and B
D. Neither - ANSWER-C
Which of the following is not correct in the procedure for preparing a
brake rotor for machining?
A. Use a micrometer to check for thickness variations
B. Use a micrometer to check the thickness of the rotor
C. Use a brake micrometer to measure the diameter
D. Use a micrometer to measure parallelism - ANSWER-C
A car equipped with a vacuum assist power brake system needs an
abnormal amount of pedal effort to stop the car, which of the following
could be the cause?
A. An internal master cylinder leak
B. Too much vacuum is applied to the booster
C. A plugged booster air breather
D. Low fluid level - ANSWER-C
While diagnosing a braking problem on a car equipped with a vacuum
power booster: Tech A says excessive pedal travel can because by a
3|Page
, leaking brake valve. Tech B says excessive pedal travel can be caused by
an improperly adjusted master cylinder push rod. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-B
Tech A uses a silencer belt only on the brake rotors that have heavy heat
checks while machining them. Tech B always machines a brake rotor to
the minimum thickness allowed. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-D
The brakes of a car chatter when they are applied, which of the
following could cause this problem?
A. A loose metering valve
B. insufficient clearance between the rotor and brake pads
4|Page
