CCNA 3 (VERSION 7.00) ENSA
PRACTICE FINAL EXAM ANSWERS
AND ANSWERS WITH CORRECT
SOLUTIONS 100% UPDATE 2026
Which two statements describe remote access VPNs? (Choose two.) - - Client software
is usually required to be able to access the network.
- Remote access VPNs support the needs of telecommuters and mobile users.
Refer to the exhibit. If the switch reboots and all routers have to re-establish OSPF
adjacencies, which routers will become the new DR and BDR? - Router R4 will become
the DR and router R1 will become the BDR.
Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco
routers as shown. The routers are unable to form a neighbor adjacency. What should be
done to fix the problem? - Change the IP address on S0/0 of router R2 to 192.168.20.2.
What are the two purposes of an OSPF router ID? (Choose two.) - - to uniquely identify
the router within the OSPF domain
- to facilitate router participation in the election of the designated router
Which command will a network engineer issue to verify the configured hello and dead
timer intervals on a point-to-point WAN link between two routers that are running
OSPFv2? - show ip ospf interface serial 0/0/0
Refer to the exhibit. What is the OSPF cost to reach the router A LAN 172.16.1.0/24
from B? - 65
Refer to the exhibit. Which data format is used to represent the data for network
automation applications? - YAML
A user is reading a book from the website
https://www.books-info.com/author1a/book2.html#page100 . Which part of the web link
is called a fragment? - #page100
Refer to the exhibit. Why are routers R1 and R2 not able to establish an OSPF
adjacency? - The serial interfaces are not in the same area.
A network technician has used the access-list 1 permit 172.16.0.0 0.0.0.255 command
to configure NAT on an edge router to translate only four networks, 172.16.0.0 /24,
, 172.16.1.0 /24, 172.16.2.0 /24, and 172.16.3.0 /24. After receiving complaints about
limited access to the Internet, issuing the show ip nat translations command reveals that
some networks are missing from the output. Which change will resolve the problem? -
The access list should be replaced with access-list 1 permit 172.16.0.0 0.0.3.255
Which type of tool would an administrator use to capture packets that are going to and
from a particular device? - protocol analyzer
A user reports that the workstation cannot connect to a networked printer in the office in
order to print a report created with word processing software. Which troubleshooting
action by the helpdesk technician would follow the divide-and-conquer approach? - Ask
the user to issue the ipconfig command
Match the OSPF state with the order in which it occurs. (Not all options are used.) -
When an OSPF network is converged and no network topology change has been
detected by a router, how often will LSU packets be sent to neighboring routers? - every
30 minutes
Which type of OSPFv2 packet contains an abbreviated list of the LSDB of a sending
router and is used by receiving routers to check against the local LSDB? - database
description
Which step in the link-state routing process is described by a router building a link-state
database based on received LSAs? - building the topology table
Refer to the exhibit. A network administrator has configured ACL 9 as shown. Users on
the 172.31.1.0 /24 network cannot forward traffic through router CiscoVille. What is the
most likely cause of the traffic failure? - The sequence of the ACEs is incorrect.
A technician is tasked with using ACLs to secure a router. When would the technician
use the access-class 20 in configuration option or command? - to secure administrative
access to the router
Refer to the exhibit. A network administrator is configuring a standard IPv4 ACL. What
is the effect after the command no access-list 10 is entered? - ACL 10 is removed from
the running configuration.
An administrator has configured an access list on R1 to allow SSH administrative
access from host 172.16.1.100. Which command correctly applies the ACL? -
R1(config-line)# access-class 1 in
Refer to the exhibit. The network administrator that has the IP address of 10.0.70.23/25
needs to have access to the corporate FTP server (10.0.54.5/28). The FTP server is
also a web server that is accessible to all internal employees on networks within the
10.x.x.x address. No other traffic should be allowed to this server.
PRACTICE FINAL EXAM ANSWERS
AND ANSWERS WITH CORRECT
SOLUTIONS 100% UPDATE 2026
Which two statements describe remote access VPNs? (Choose two.) - - Client software
is usually required to be able to access the network.
- Remote access VPNs support the needs of telecommuters and mobile users.
Refer to the exhibit. If the switch reboots and all routers have to re-establish OSPF
adjacencies, which routers will become the new DR and BDR? - Router R4 will become
the DR and router R1 will become the BDR.
Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco
routers as shown. The routers are unable to form a neighbor adjacency. What should be
done to fix the problem? - Change the IP address on S0/0 of router R2 to 192.168.20.2.
What are the two purposes of an OSPF router ID? (Choose two.) - - to uniquely identify
the router within the OSPF domain
- to facilitate router participation in the election of the designated router
Which command will a network engineer issue to verify the configured hello and dead
timer intervals on a point-to-point WAN link between two routers that are running
OSPFv2? - show ip ospf interface serial 0/0/0
Refer to the exhibit. What is the OSPF cost to reach the router A LAN 172.16.1.0/24
from B? - 65
Refer to the exhibit. Which data format is used to represent the data for network
automation applications? - YAML
A user is reading a book from the website
https://www.books-info.com/author1a/book2.html#page100 . Which part of the web link
is called a fragment? - #page100
Refer to the exhibit. Why are routers R1 and R2 not able to establish an OSPF
adjacency? - The serial interfaces are not in the same area.
A network technician has used the access-list 1 permit 172.16.0.0 0.0.0.255 command
to configure NAT on an edge router to translate only four networks, 172.16.0.0 /24,
, 172.16.1.0 /24, 172.16.2.0 /24, and 172.16.3.0 /24. After receiving complaints about
limited access to the Internet, issuing the show ip nat translations command reveals that
some networks are missing from the output. Which change will resolve the problem? -
The access list should be replaced with access-list 1 permit 172.16.0.0 0.0.3.255
Which type of tool would an administrator use to capture packets that are going to and
from a particular device? - protocol analyzer
A user reports that the workstation cannot connect to a networked printer in the office in
order to print a report created with word processing software. Which troubleshooting
action by the helpdesk technician would follow the divide-and-conquer approach? - Ask
the user to issue the ipconfig command
Match the OSPF state with the order in which it occurs. (Not all options are used.) -
When an OSPF network is converged and no network topology change has been
detected by a router, how often will LSU packets be sent to neighboring routers? - every
30 minutes
Which type of OSPFv2 packet contains an abbreviated list of the LSDB of a sending
router and is used by receiving routers to check against the local LSDB? - database
description
Which step in the link-state routing process is described by a router building a link-state
database based on received LSAs? - building the topology table
Refer to the exhibit. A network administrator has configured ACL 9 as shown. Users on
the 172.31.1.0 /24 network cannot forward traffic through router CiscoVille. What is the
most likely cause of the traffic failure? - The sequence of the ACEs is incorrect.
A technician is tasked with using ACLs to secure a router. When would the technician
use the access-class 20 in configuration option or command? - to secure administrative
access to the router
Refer to the exhibit. A network administrator is configuring a standard IPv4 ACL. What
is the effect after the command no access-list 10 is entered? - ACL 10 is removed from
the running configuration.
An administrator has configured an access list on R1 to allow SSH administrative
access from host 172.16.1.100. Which command correctly applies the ACL? -
R1(config-line)# access-class 1 in
Refer to the exhibit. The network administrator that has the IP address of 10.0.70.23/25
needs to have access to the corporate FTP server (10.0.54.5/28). The FTP server is
also a web server that is accessible to all internal employees on networks within the
10.x.x.x address. No other traffic should be allowed to this server.