CUSP T&D EXAM QUESTIONS AND
CORRECT ANSWERS||100%
GUARANTEED PASS||A+
GRADED||UPDATED 2026/2027
SYLLABUS||<<LATEST VERSION>>
How should leaders inspire people? - ANSWER ✓ Through positive personal
examples, good management practices and a good sense of moral responsibility.
Joint safety and health committees ___ . - ANSWER ✓ Promote a broader base of
expertise and experience.
the definition of a buffer space in a temporary traffic control zone would include: -
ANSWER ✓ The lateral and longitudinal area that serves as recovery space fro
errant vehicles.
The language, 'Tags shall prohibit operation of the disconnecting means and shall
indicate that employees are at work', is associated with which standards section? -
ANSWER ✓ Lockout tag out.
One purpose for including workforce safety review in the design and engineering
process is: - ANSWER ✓ Incorporating safety and training for affected workplace
users.
To ensure an extension ladder leaned against a wall is at the right angle, the ratio
of height at the top of the ladder to the distance the feet are from the eall at the
bottom of the ladder should be: - ANSWER ✓ 4:1
Atmospheric hazards include: - ANSWER ✓ Oxygen deficiency/enriched, toxic
gases and flammable atmospheres.
Hazards are typically ranked according to likelihood of occurrence. The likelihood
scale includes all of the following, EXCEPT: - ANSWER ✓ Never.
, Hazards are typically ranked according to likelihood of occurrence. The likelihood
scale includes all of the following: - ANSWER ✓ Frequent, probable and remote.
Monitoring is used to assess the effectiveness of controls on identified hazards.
Common monitoring modes include: - ANSWER ✓ Inspections and medical
monitoring.
Within the system, a latent organizational error is usually discovered: - ANSWER
✓ During post-incident investigation.
During storm restoration workers are on a foreign system. Utility systems are
destroyed, system maps are unavailable. As they approach the work, the equipment
they must replace they have never worked with before and the construction is
unfamiliar. Still, they successfully and safely restore the system without error.
Most likely they solved their problems in a: - ANSWER ✓ Rule-based
performance mode.
A maintenance crew is working to replace a vibration transmitter on a generator
frame. They ran into problems, but used trial and error to find out what was wrong,
leading to a plan for repair. This is an example of: - ANSWER ✓ Knowledge-
based performance mode.
Against policy, a manager lets workers go without hard hats because he personally
decides there are more important things to worry about. This is an example of: -
ANSWER ✓ A latent organizational weakness.
Pre-task hazard analysis, crew safety meetings and job site inspections work best
toward a safe workplace when conducted by: - ANSWER ✓ Crew leaders assisted
by crew members.
A good way for managers to ensure workers understand policy and follow rules is
to: - ANSWER ✓ Visit job sites, take a real interest in employees and talk to
workers.
If a supervisor observes a worker not wearing their safety glasses when they are
required and says nothing to the worker, the supervisor: - ANSWER ✓ Has
reinforced the bad habit that safety glasses are optional.
, What best describes common elements of trench safety? - ANSWER ✓ Benching,
shoring and sloping.
Equipment operators must comply with specifications and limitations in regard to
the operation of cranes and derricks. Where are specifications and limitations
found? - ANSWER ✓ Manufacturer operator's manual.
The employer shall ensure that the employee in charge conducts a job briefing
with the employees involved before they start each job. The briefing will cover at
least the following subjects: - ANSWER ✓ Hazards associated with the job, work
procedures involved, special precautions, energy source controls and PPE
requirements.
What is NOT a requirement for safety glasses by CSA's Z94.3.1 PPE standard? -
ANSWER ✓ Safety glasses must be marked with the legend CSA Z94.3.1.
What are the requirements for safety glasses by CSA's Z94.3.1 PPE standard? -
ANSWER ✓ 1. Side shields may be fixed, clip-on or slip-on.
2. Safety glasses must be marked with the manufacturer's name or logo.
3. Glasses be proper tint for the work environment.
The reason for the standardizing stop sign dimensions, shape and colour is best
described by: - ANSWER ✓ Shape, size and colour is instantly recognizable,
causing a programmed safety response.
Class A fires include which class of burning materials? - ANSWER ✓ Paper,
wood and cloth.
The acronym GFCI stands for: - ANSWER ✓ Ground Fault Circuit Interrupter
Under most provincial Workers Compensation Acts, the prime contractor or
owner has: - ANSWER ✓ The leverage to assure compliance with safety standards
by subcontractors.
T/F: Only a qualified observer may use hand signals to halt the movement of a
crane in an emergency. - ANSWER ✓ False
CORRECT ANSWERS||100%
GUARANTEED PASS||A+
GRADED||UPDATED 2026/2027
SYLLABUS||<<LATEST VERSION>>
How should leaders inspire people? - ANSWER ✓ Through positive personal
examples, good management practices and a good sense of moral responsibility.
Joint safety and health committees ___ . - ANSWER ✓ Promote a broader base of
expertise and experience.
the definition of a buffer space in a temporary traffic control zone would include: -
ANSWER ✓ The lateral and longitudinal area that serves as recovery space fro
errant vehicles.
The language, 'Tags shall prohibit operation of the disconnecting means and shall
indicate that employees are at work', is associated with which standards section? -
ANSWER ✓ Lockout tag out.
One purpose for including workforce safety review in the design and engineering
process is: - ANSWER ✓ Incorporating safety and training for affected workplace
users.
To ensure an extension ladder leaned against a wall is at the right angle, the ratio
of height at the top of the ladder to the distance the feet are from the eall at the
bottom of the ladder should be: - ANSWER ✓ 4:1
Atmospheric hazards include: - ANSWER ✓ Oxygen deficiency/enriched, toxic
gases and flammable atmospheres.
Hazards are typically ranked according to likelihood of occurrence. The likelihood
scale includes all of the following, EXCEPT: - ANSWER ✓ Never.
, Hazards are typically ranked according to likelihood of occurrence. The likelihood
scale includes all of the following: - ANSWER ✓ Frequent, probable and remote.
Monitoring is used to assess the effectiveness of controls on identified hazards.
Common monitoring modes include: - ANSWER ✓ Inspections and medical
monitoring.
Within the system, a latent organizational error is usually discovered: - ANSWER
✓ During post-incident investigation.
During storm restoration workers are on a foreign system. Utility systems are
destroyed, system maps are unavailable. As they approach the work, the equipment
they must replace they have never worked with before and the construction is
unfamiliar. Still, they successfully and safely restore the system without error.
Most likely they solved their problems in a: - ANSWER ✓ Rule-based
performance mode.
A maintenance crew is working to replace a vibration transmitter on a generator
frame. They ran into problems, but used trial and error to find out what was wrong,
leading to a plan for repair. This is an example of: - ANSWER ✓ Knowledge-
based performance mode.
Against policy, a manager lets workers go without hard hats because he personally
decides there are more important things to worry about. This is an example of: -
ANSWER ✓ A latent organizational weakness.
Pre-task hazard analysis, crew safety meetings and job site inspections work best
toward a safe workplace when conducted by: - ANSWER ✓ Crew leaders assisted
by crew members.
A good way for managers to ensure workers understand policy and follow rules is
to: - ANSWER ✓ Visit job sites, take a real interest in employees and talk to
workers.
If a supervisor observes a worker not wearing their safety glasses when they are
required and says nothing to the worker, the supervisor: - ANSWER ✓ Has
reinforced the bad habit that safety glasses are optional.
, What best describes common elements of trench safety? - ANSWER ✓ Benching,
shoring and sloping.
Equipment operators must comply with specifications and limitations in regard to
the operation of cranes and derricks. Where are specifications and limitations
found? - ANSWER ✓ Manufacturer operator's manual.
The employer shall ensure that the employee in charge conducts a job briefing
with the employees involved before they start each job. The briefing will cover at
least the following subjects: - ANSWER ✓ Hazards associated with the job, work
procedures involved, special precautions, energy source controls and PPE
requirements.
What is NOT a requirement for safety glasses by CSA's Z94.3.1 PPE standard? -
ANSWER ✓ Safety glasses must be marked with the legend CSA Z94.3.1.
What are the requirements for safety glasses by CSA's Z94.3.1 PPE standard? -
ANSWER ✓ 1. Side shields may be fixed, clip-on or slip-on.
2. Safety glasses must be marked with the manufacturer's name or logo.
3. Glasses be proper tint for the work environment.
The reason for the standardizing stop sign dimensions, shape and colour is best
described by: - ANSWER ✓ Shape, size and colour is instantly recognizable,
causing a programmed safety response.
Class A fires include which class of burning materials? - ANSWER ✓ Paper,
wood and cloth.
The acronym GFCI stands for: - ANSWER ✓ Ground Fault Circuit Interrupter
Under most provincial Workers Compensation Acts, the prime contractor or
owner has: - ANSWER ✓ The leverage to assure compliance with safety standards
by subcontractors.
T/F: Only a qualified observer may use hand signals to halt the movement of a
crane in an emergency. - ANSWER ✓ False
