1|Page
NACE CIP 1 CBT Exam (Quizzes and Study Questions)
|| Most Recent Exam Actual Complete Real Verified
Exam Questions And Correct Answers (Verified
Answers) Already Graded A+ || Newest Exam!!!
What is the minimum recommended distance away from
an edge that an inspector should take a measurement with
a dial type magnetic pull off Dry Film Thickness(DFT)
gauge? - Answer-2.5 cm (1 inch)
Polymerization is the process of? - Answer-Monomers
joining together.
An exposed area of the substrate or previous coat of a
conductive material, often caused by poor application
technique is called: - Answer-Holiday
Checking is: - Answer-a fine crack in the surface of a
coating that rarely reaches the substrate.
Inspection documentation is important because: - Answer-
Owners use the documentation for a variety of purposes.
,2|Page
An Inspectors personal log book should contain: - Answer-
No comments regarding the application team.
You have just received your NACE CIP Level 1
certification when you are asked to supervise a team of
uncertified field pipeline inspectors. Your FIRST preferred
course of action is to: - Answer-Review the NACE
Attestation prior to making a decision.
Good record can provide maintenance departments with
detailed information about ALL of the following EXCEPT: -
Answer-How the item was coated.
Non Conformance Reports are completed by the
Inspector: - Answer-When the Inspector and Contractor
deem it to be significant non conforming item.
The initial steel condition is important to the NACE
Inspector because: - Answer-The Inspector may have to
reject the steel.
,3|Page
The form of corrosion that has the largest potential for
unexpected catastrophic failure is: - Answer-Galvanic
Corrosion
What is used to determine compressed air cleanliness? -
Answer-Profilometer
Dew point is the temperature at which - Answer-
condensation occurs.
You are the NACE Inspector on a tank lining project where
a 50% solids epoxy tank lining is being applied. After
application of the 19 coat you notice small blisters in some
areas of the applied lining. Your FIRST preferred course of
action is to: - Answer-Document the problem and advise
the Contractor and Owner's representative.
If a contractor is using a poorly maintained compressor to
supply air for abrasive blast cleaning and conventional
airspray, the coating inspector should perform a - Answer-
blotter test for the presence of oil and water.
Upon arrival of coating materials, the inspector should -
Answer-observe and document the amount of material
and batch numbers.
, 4|Page
Relative humidity is - Answer-a measure of the amount of
moisture in the air compared to saturation level.
Galvanic corrosion occurs on which of the following
substrates? - Answer-Metal
When applying Thermal Spray Coatings the specification
is most likely to reference: - Answer-SSPC-CS 23.00/AWS
C2.23/NACE No. 12
Osmotic blistering is most likely to occur as a result of: -
Answer-Airless spray application.
When performing tests for oil and grease using an ultra
violet light, the NACE Inspector should be aware that: -
Answer-Synthetic oil or grease may not be identified.
To achieve consistently accurate results with ALL alt test
equipment: - Answer-wash your hands before sampling.
NACE CIP 1 CBT Exam (Quizzes and Study Questions)
|| Most Recent Exam Actual Complete Real Verified
Exam Questions And Correct Answers (Verified
Answers) Already Graded A+ || Newest Exam!!!
What is the minimum recommended distance away from
an edge that an inspector should take a measurement with
a dial type magnetic pull off Dry Film Thickness(DFT)
gauge? - Answer-2.5 cm (1 inch)
Polymerization is the process of? - Answer-Monomers
joining together.
An exposed area of the substrate or previous coat of a
conductive material, often caused by poor application
technique is called: - Answer-Holiday
Checking is: - Answer-a fine crack in the surface of a
coating that rarely reaches the substrate.
Inspection documentation is important because: - Answer-
Owners use the documentation for a variety of purposes.
,2|Page
An Inspectors personal log book should contain: - Answer-
No comments regarding the application team.
You have just received your NACE CIP Level 1
certification when you are asked to supervise a team of
uncertified field pipeline inspectors. Your FIRST preferred
course of action is to: - Answer-Review the NACE
Attestation prior to making a decision.
Good record can provide maintenance departments with
detailed information about ALL of the following EXCEPT: -
Answer-How the item was coated.
Non Conformance Reports are completed by the
Inspector: - Answer-When the Inspector and Contractor
deem it to be significant non conforming item.
The initial steel condition is important to the NACE
Inspector because: - Answer-The Inspector may have to
reject the steel.
,3|Page
The form of corrosion that has the largest potential for
unexpected catastrophic failure is: - Answer-Galvanic
Corrosion
What is used to determine compressed air cleanliness? -
Answer-Profilometer
Dew point is the temperature at which - Answer-
condensation occurs.
You are the NACE Inspector on a tank lining project where
a 50% solids epoxy tank lining is being applied. After
application of the 19 coat you notice small blisters in some
areas of the applied lining. Your FIRST preferred course of
action is to: - Answer-Document the problem and advise
the Contractor and Owner's representative.
If a contractor is using a poorly maintained compressor to
supply air for abrasive blast cleaning and conventional
airspray, the coating inspector should perform a - Answer-
blotter test for the presence of oil and water.
Upon arrival of coating materials, the inspector should -
Answer-observe and document the amount of material
and batch numbers.
, 4|Page
Relative humidity is - Answer-a measure of the amount of
moisture in the air compared to saturation level.
Galvanic corrosion occurs on which of the following
substrates? - Answer-Metal
When applying Thermal Spray Coatings the specification
is most likely to reference: - Answer-SSPC-CS 23.00/AWS
C2.23/NACE No. 12
Osmotic blistering is most likely to occur as a result of: -
Answer-Airless spray application.
When performing tests for oil and grease using an ultra
violet light, the NACE Inspector should be aware that: -
Answer-Synthetic oil or grease may not be identified.
To achieve consistently accurate results with ALL alt test
equipment: - Answer-wash your hands before sampling.
