MASSACHUSETTS OIL BURNER PRACTICE EXAM 2026 – COMPLETE QUESTION
BANK WITH CORRECT AND VERIFIED ANSWERS, GRADED A+
Which of the following should be worn when using power tools?
a) Safety glasses
b) A hard hat
c) Leather gloves
d) Safety boots -
e) Answer-A
What is the minimum acceptable type of respiratory protection to be used when cleaning a soot filled
furnace? -
Answer-Disposable Filter Masks
What is the proper vertical to horizontal distance ratio for ladder placement? -
Answer-3:1 or 4:1
What muscles or parts of your body should you primarily use to lift a weight from the floor? -
Answer-Stomach muscles and legs
When changing a drill bit or saw blade on a power tool, what is first action that you should take? -
Answer-Disconnect from the power source
Name two safety concerns created by the customer's housekeeping practices? -
Answer-Messy and poor lit work areas
Name two areas that each of the following substances may be encountered in the oil heat trade:
Asbestos and Silica: -
Answer-Insulation, older ceiling tile
Refactory material, cement
You must never use a chisel with a head -
,Answer-Mushroomed
,Name three types of pliers: -
Answer-Side locked Linesman
Needle-nose
A wrench is better suited to loosening tight nuts. -
Answer-Box
Name three types of snips: -
Answer-Combination Compound
Straight
A masonry drill bit is suited for drilling into concrete due to its tip -
Answer-Carbide
hammers are best suited for striking chisels. -
Answer-Ball Peen
Name three types of screwdrivers: -
Answer-Phillips Robertson
Slotted
should be used when making sharp turn cuts in sheet metal? -
Answer-Compound Snips (Aviation Snips)
Name four types of wrenches -
Answer-Open end, box end, cominations , adjustable
Pliers should not be exposed to excessive: -
Answer-Heat
, and determine a screw size. -
Answer-Length and Diameter
A is used to anchor into a hollow wall. -
Answer-Toggle Bolt
True or False:
Sheet metal screws are self tapping. -
Answer-True
" " cleat and an " " cleat are used to join sheet metal connections. -
Answer-"S" and "Drive"
Name three types of screw heads: -
Answer-Philips, Robertson, Slotted
A round headed bolt is called a: -
Answer-Carriage Bolt
Name the two types of thread forms: -
Answer-National Fine, National Course
A hole is required to start most screw types. -
Answer-Pilot
A sheet metal joint can be further sealed with the use of -
Answer-High temp foil tape
Washers help prevent a nut from: -
Answer-Loosening
The volume of a structure which measures 10 ' long x 6 ' wide x 8 high is: -
BANK WITH CORRECT AND VERIFIED ANSWERS, GRADED A+
Which of the following should be worn when using power tools?
a) Safety glasses
b) A hard hat
c) Leather gloves
d) Safety boots -
e) Answer-A
What is the minimum acceptable type of respiratory protection to be used when cleaning a soot filled
furnace? -
Answer-Disposable Filter Masks
What is the proper vertical to horizontal distance ratio for ladder placement? -
Answer-3:1 or 4:1
What muscles or parts of your body should you primarily use to lift a weight from the floor? -
Answer-Stomach muscles and legs
When changing a drill bit or saw blade on a power tool, what is first action that you should take? -
Answer-Disconnect from the power source
Name two safety concerns created by the customer's housekeeping practices? -
Answer-Messy and poor lit work areas
Name two areas that each of the following substances may be encountered in the oil heat trade:
Asbestos and Silica: -
Answer-Insulation, older ceiling tile
Refactory material, cement
You must never use a chisel with a head -
,Answer-Mushroomed
,Name three types of pliers: -
Answer-Side locked Linesman
Needle-nose
A wrench is better suited to loosening tight nuts. -
Answer-Box
Name three types of snips: -
Answer-Combination Compound
Straight
A masonry drill bit is suited for drilling into concrete due to its tip -
Answer-Carbide
hammers are best suited for striking chisels. -
Answer-Ball Peen
Name three types of screwdrivers: -
Answer-Phillips Robertson
Slotted
should be used when making sharp turn cuts in sheet metal? -
Answer-Compound Snips (Aviation Snips)
Name four types of wrenches -
Answer-Open end, box end, cominations , adjustable
Pliers should not be exposed to excessive: -
Answer-Heat
, and determine a screw size. -
Answer-Length and Diameter
A is used to anchor into a hollow wall. -
Answer-Toggle Bolt
True or False:
Sheet metal screws are self tapping. -
Answer-True
" " cleat and an " " cleat are used to join sheet metal connections. -
Answer-"S" and "Drive"
Name three types of screw heads: -
Answer-Philips, Robertson, Slotted
A round headed bolt is called a: -
Answer-Carriage Bolt
Name the two types of thread forms: -
Answer-National Fine, National Course
A hole is required to start most screw types. -
Answer-Pilot
A sheet metal joint can be further sealed with the use of -
Answer-High temp foil tape
Washers help prevent a nut from: -
Answer-Loosening
The volume of a structure which measures 10 ' long x 6 ' wide x 8 high is: -
