Georgia Conditioned Air Contractor
Class I Examination Questions And
Correct Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
Pdf
1. What is the maximum cooling capacity allowed for a Class I licensed
conditioned air system under Georgia regulations?
A) 40,000 BTU
B) 60,000 BTU
C) 90,000 BTU
D) 100,000 BTU
Rationale: Class I is restricted to systems not exceeding 60,000 BTU
cooling capacity. 1
2. Which Georgia code book is referenced for mechanical installations in
the exam?
A) Florida Mechanical Code
B) Uniform Mechanical Code
C) 2018 International Mechanical Code with Georgia amendments
D) ANSI Mechanical Code
Rationale: Georgia uses the 2018 IMC (with state amendments) as a
reference.
3. What minimum years of experience are required to qualify for the
Class I exam?
A) 2 years
B) 4 years
, C) 5 years
D) 6 years
Rationale: Class I applicants must document four years of HVAC
experience. ServiceTitan
4. Which of the following is not considered conditioned air contracting
under Georgia rules?
A) Installation of HVAC systems
B) Repair of HVAC systems
C) Painting HVAC ducts
D) Service of HVAC equipment
Rationale: Painting ducts is not HVAC contracting work. 1
5. How often must a Georgia conditioned air contractor license be
renewed?
A) Every year
B) Every two years
C) Every three years
D) Every five years
Rationale: Licenses renew biennially with continuing education
requirements.
6. Which protective certification is required before handling
refrigerants?
A) Class A Electrical Certification
B) EPA Section 608 Certification
C) OSHA Forklift Certification
D) Georgia Gas Piping Card
Rationale: EPA 608 is federally required for refrigerants.
7. What does OSHA stand for?
A) Occupational Safety and Heating Administration
B) Occupational Safety and Health Administration
C) Office of Safety and Hazard Assessment
D) Organization of Standards for HVAC
Rationale: Standard federal safety regulatory body.
8. A duct system design calculation for airflow is typically derived from
which manual?
A) Manual M
, B) Manual D
C) Manual R
D) Manual F
Rationale: Manual D covers residential duct design.
9. Which tool is used to calculate residential heat load?
A) Psychrometer
B) Manual J
C) Anemometer
D) Voltmeter
Rationale: Manual J is the load calculation standard.
10. What safety gear should be used when brazing refrigerant lines?
A) Flip flops
B) Shorts
C) Eye protection and gloves
D) No protective gear
Rationale: PPE is essential for brazing safety.
11. In Georgia, who must sign off on references for experience?
A) Any coworker
B) Family member
C) Architect, Professional Engineer, Inspector, or licensed
conditioned air contractor
D) Customer
Rationale: These are the acceptable reference sources in application.
12. What is the main function of a thermostat?
A) Increase refrigerant pressure
B) Heat air directly
C) Regulate temperature by signaling equipment
D) Reduce airflow
Rationale: Thermostats control HVAC operation based on set
temperatures.
13. Which document sets the electrical standards referenced in
Georgia HVAC code?
A) Georgia Plumbing Code
B) NFPA Fire Code
C) 2017 National Electrical Code
Class I Examination Questions And
Correct Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
1. What is the maximum cooling capacity allowed for a Class I licensed
conditioned air system under Georgia regulations?
A) 40,000 BTU
B) 60,000 BTU
C) 90,000 BTU
D) 100,000 BTU
Rationale: Class I is restricted to systems not exceeding 60,000 BTU
cooling capacity. 1
2. Which Georgia code book is referenced for mechanical installations in
the exam?
A) Florida Mechanical Code
B) Uniform Mechanical Code
C) 2018 International Mechanical Code with Georgia amendments
D) ANSI Mechanical Code
Rationale: Georgia uses the 2018 IMC (with state amendments) as a
reference.
3. What minimum years of experience are required to qualify for the
Class I exam?
A) 2 years
B) 4 years
, C) 5 years
D) 6 years
Rationale: Class I applicants must document four years of HVAC
experience. ServiceTitan
4. Which of the following is not considered conditioned air contracting
under Georgia rules?
A) Installation of HVAC systems
B) Repair of HVAC systems
C) Painting HVAC ducts
D) Service of HVAC equipment
Rationale: Painting ducts is not HVAC contracting work. 1
5. How often must a Georgia conditioned air contractor license be
renewed?
A) Every year
B) Every two years
C) Every three years
D) Every five years
Rationale: Licenses renew biennially with continuing education
requirements.
6. Which protective certification is required before handling
refrigerants?
A) Class A Electrical Certification
B) EPA Section 608 Certification
C) OSHA Forklift Certification
D) Georgia Gas Piping Card
Rationale: EPA 608 is federally required for refrigerants.
7. What does OSHA stand for?
A) Occupational Safety and Heating Administration
B) Occupational Safety and Health Administration
C) Office of Safety and Hazard Assessment
D) Organization of Standards for HVAC
Rationale: Standard federal safety regulatory body.
8. A duct system design calculation for airflow is typically derived from
which manual?
A) Manual M
, B) Manual D
C) Manual R
D) Manual F
Rationale: Manual D covers residential duct design.
9. Which tool is used to calculate residential heat load?
A) Psychrometer
B) Manual J
C) Anemometer
D) Voltmeter
Rationale: Manual J is the load calculation standard.
10. What safety gear should be used when brazing refrigerant lines?
A) Flip flops
B) Shorts
C) Eye protection and gloves
D) No protective gear
Rationale: PPE is essential for brazing safety.
11. In Georgia, who must sign off on references for experience?
A) Any coworker
B) Family member
C) Architect, Professional Engineer, Inspector, or licensed
conditioned air contractor
D) Customer
Rationale: These are the acceptable reference sources in application.
12. What is the main function of a thermostat?
A) Increase refrigerant pressure
B) Heat air directly
C) Regulate temperature by signaling equipment
D) Reduce airflow
Rationale: Thermostats control HVAC operation based on set
temperatures.
13. Which document sets the electrical standards referenced in
Georgia HVAC code?
A) Georgia Plumbing Code
B) NFPA Fire Code
C) 2017 National Electrical Code
