100 ELEVATOR PRACTICE PAPER 2026
COMPLETE SOLUTIONS
◉ The minimum clearance form the floor to the suspended ceiling is:
a. 80"
b. 96"
c. 7'3"
d. 8'2". Answer: a. 80"
◉ what should you be aware of when removing a cab for
replacement?
a. The weight that is to be removed from the ceiling.
b. The original weight and counterbalancing.
c. How much the cab was out of square.
d. Cover the panels so they do not get banged up.. Answer: b. The
original weight and counterbalancing.
◉ When fans are used on modernization jobs for exhausting fumes,
what statement is correct?
a. They're to keep you cool, not for exhausting fumes.
b. They should direct the fumes into the hoistway.
c. They should direct the fumes into the pit.
,d. They should direct the fumes to the outside.. Answer: d. They
should direct the fumes to the outside.
◉ The star symbol is used on the COP for what?
a. To show where the floor buttons are located.
b. To designate the main floor.
c. To make the door buttons stand out.
d. To show the alarm bell location.. Answer: b. To designate the main
floor.
◉ Using a laminate stop strip against the fence on a table saw:
a. Keeps the laminate straight to the blade.
b. Keeps the laminate from lifting off the blade.
c. Keeps the laminate from slipping under the fence.
d. Keeps the laminate from going over the fence.. Answer: c. Keeps
the laminate from slipping under the fence.
◉ The contact adhesives must be ________ before final bonding:
a. 85 degrees
b. Dry
c. Wet to touch
d. Cold. Answer: b. Dry
,◉ What is the most important piece of equipment you have when
using a power saw?
a. Combination blade
b. Safety glasses
c. Wood rule
d. Framing square. Answer: b. safety glasses
◉ When using a circular saw, which of the following is correct?
a. Never start the cut until the blade is turning full RPM
b. The base is not adjustable for cutting depth
c. Circular saw blades range from 10 to 16 inches
d. Remove the retractable guard before cutting. Answer: a. Never
start the cut until the blade is turning full RPM
◉ What is used to make crosscuts on a table saw?
a. Push stick
b. Rip fence
c. Miter gauge
d. Larger Blade. Answer: c. Miter saw
, ◉ When making crosscuts with a radial arm saw which statement is
correct?
a. Push the wood slowly into the blade.
b. Restrain the blade from moving too fast.
c. Rotate and lock the blade parallel to the guide.
d. Adjust the blade 1/4" above to cutting surface. Answer: b. Restrain
the blade from moving too fast
◉ What are the two things a compound mitre saw does best at the
same time?
a. moving it around and setting it up is fast.
b. You can cut left and right at the same time.
c. Tilting the blade 45 degrees and pivoting the table 45 degrees
gives you a 90 degree square cut.
d. bevel and mitre cuts can be made at the same time. Answer: d.
bevel and mitre cuts can be made at the same time
◉ Why do we use laminated glass in the walls of glass elevator cabs?
a. if the glass breaks you can get a replacement at the hardware
store.
b. if the glass cracks the plastic interlayer holds the fragments
c. it is made in a variety of colors
d. it is easy to handle and installs quickly. Answer: b. if the glass
cracks the plastic interlayer holds the fragments
COMPLETE SOLUTIONS
◉ The minimum clearance form the floor to the suspended ceiling is:
a. 80"
b. 96"
c. 7'3"
d. 8'2". Answer: a. 80"
◉ what should you be aware of when removing a cab for
replacement?
a. The weight that is to be removed from the ceiling.
b. The original weight and counterbalancing.
c. How much the cab was out of square.
d. Cover the panels so they do not get banged up.. Answer: b. The
original weight and counterbalancing.
◉ When fans are used on modernization jobs for exhausting fumes,
what statement is correct?
a. They're to keep you cool, not for exhausting fumes.
b. They should direct the fumes into the hoistway.
c. They should direct the fumes into the pit.
,d. They should direct the fumes to the outside.. Answer: d. They
should direct the fumes to the outside.
◉ The star symbol is used on the COP for what?
a. To show where the floor buttons are located.
b. To designate the main floor.
c. To make the door buttons stand out.
d. To show the alarm bell location.. Answer: b. To designate the main
floor.
◉ Using a laminate stop strip against the fence on a table saw:
a. Keeps the laminate straight to the blade.
b. Keeps the laminate from lifting off the blade.
c. Keeps the laminate from slipping under the fence.
d. Keeps the laminate from going over the fence.. Answer: c. Keeps
the laminate from slipping under the fence.
◉ The contact adhesives must be ________ before final bonding:
a. 85 degrees
b. Dry
c. Wet to touch
d. Cold. Answer: b. Dry
,◉ What is the most important piece of equipment you have when
using a power saw?
a. Combination blade
b. Safety glasses
c. Wood rule
d. Framing square. Answer: b. safety glasses
◉ When using a circular saw, which of the following is correct?
a. Never start the cut until the blade is turning full RPM
b. The base is not adjustable for cutting depth
c. Circular saw blades range from 10 to 16 inches
d. Remove the retractable guard before cutting. Answer: a. Never
start the cut until the blade is turning full RPM
◉ What is used to make crosscuts on a table saw?
a. Push stick
b. Rip fence
c. Miter gauge
d. Larger Blade. Answer: c. Miter saw
, ◉ When making crosscuts with a radial arm saw which statement is
correct?
a. Push the wood slowly into the blade.
b. Restrain the blade from moving too fast.
c. Rotate and lock the blade parallel to the guide.
d. Adjust the blade 1/4" above to cutting surface. Answer: b. Restrain
the blade from moving too fast
◉ What are the two things a compound mitre saw does best at the
same time?
a. moving it around and setting it up is fast.
b. You can cut left and right at the same time.
c. Tilting the blade 45 degrees and pivoting the table 45 degrees
gives you a 90 degree square cut.
d. bevel and mitre cuts can be made at the same time. Answer: d.
bevel and mitre cuts can be made at the same time
◉ Why do we use laminated glass in the walls of glass elevator cabs?
a. if the glass breaks you can get a replacement at the hardware
store.
b. if the glass cracks the plastic interlayer holds the fragments
c. it is made in a variety of colors
d. it is easy to handle and installs quickly. Answer: b. if the glass
cracks the plastic interlayer holds the fragments
