Electrical Troubleshooting WITH
COMPLETE SOLUTIONS.
open motor winding - ANSWER: condition in which an internal motor winding experiences a
break that prevents current from flowing through the winding
pitting - ANSWER: condition in which the surfaces of relay or contactor contacts become worn.
short circuit to ground - ANSWER: condition in which an internal motor conducting surface
comes in contact with the shell of the component.
shorted motor winding - ANSWER: condition in which damage to a motor winding exists,
creating a reduction in the resistance of the winding.
disconnected - ANSWER: in order to evaluate a holding coil, the wires must be:
good, shorted, or open - ANSWER: there are three possible conclusions a technician can come
to when evaluating a holding coil. What are they?
zero ohms - ANSWER: The ohms reading across a coil that is shorted and needs replacement.
infinity - ANSWER: The ohms reading across a coil that is open and needs replacement.
lowest range - ANSWER: The ohms setting on the meter to evaluate a coil.
next lowest range - ANSWER: If a holding coil's ohms reading is infinity the technician should
check again after changing the meter's setting to the
r terminal - ANSWER: Hot wire from the transformer to the thermostat that is red in color.
y terminal - ANSWER: yellow wire that carries power from the thermostat to the cooling circuit.
w terminal - ANSWER: white wire that transfers power from the thermostat to the heating circuit.
, g terminal - ANSWER: current carrying green insulated conductor that powers the indoor fan
circuit from thermostat.
24 volts - ANSWER: With the fan switch on "auto" and test probes on R and G terminals, the
voltage reading should be:
r and g - ANSWER: If the fan is in the "on" position but does not come on, a test to find out
whether you have a defective subbase, is to place a jumper between these two terminals
defective - ANSWER: When a system will not operate and a jumper is placed between terminals
R and G, and the fan starts, the subbase is
transformer - ANSWER: Non-starting indoor fan with a jumper between terminals R and G leads
the technician to search for the problem starting at the ________ or associated wiring.
subbase - ANSWER: Jumpering between terminals R and G, and finding that the fan does not
start usually means there is NO problem at the_______.
cooling circuit - ANSWER: Placing a jumper between terminals R and Y on the subbase is how
to energize the ______________
thermostat - ANSWER: If a cooling circuit runs (including compressor) only with a jumper, but
not by setting the thermostat to the cooling mode, the defective component is the
____________
heating circuit - ANSWER: Placing a jumper between terminals R and W on the subbase is how
to energize the _____________
thermostat - ANSWER: If a heating circuit runs only with a jumper, but not by setting the
thermostat to the heating mode, the defective component is the ____________
capped taped - ANSWER: To prevent the possibility of a short, unused wire leads on a multi-tap
transformer should be ______ and _______.
24 volts - ANSWER: When voltage is applied to the primary transformer winding, the secondary
should read ____________
resistance - ANSWER: A transformer that does not have a low voltage reading at the secondary
winding must be disconnected from the system and tested for ____________.
open - ANSWER: If the resistance reading across the secondary transformer winding is infinity,
the winding is ______ and needs replacement.
COMPLETE SOLUTIONS.
open motor winding - ANSWER: condition in which an internal motor winding experiences a
break that prevents current from flowing through the winding
pitting - ANSWER: condition in which the surfaces of relay or contactor contacts become worn.
short circuit to ground - ANSWER: condition in which an internal motor conducting surface
comes in contact with the shell of the component.
shorted motor winding - ANSWER: condition in which damage to a motor winding exists,
creating a reduction in the resistance of the winding.
disconnected - ANSWER: in order to evaluate a holding coil, the wires must be:
good, shorted, or open - ANSWER: there are three possible conclusions a technician can come
to when evaluating a holding coil. What are they?
zero ohms - ANSWER: The ohms reading across a coil that is shorted and needs replacement.
infinity - ANSWER: The ohms reading across a coil that is open and needs replacement.
lowest range - ANSWER: The ohms setting on the meter to evaluate a coil.
next lowest range - ANSWER: If a holding coil's ohms reading is infinity the technician should
check again after changing the meter's setting to the
r terminal - ANSWER: Hot wire from the transformer to the thermostat that is red in color.
y terminal - ANSWER: yellow wire that carries power from the thermostat to the cooling circuit.
w terminal - ANSWER: white wire that transfers power from the thermostat to the heating circuit.
, g terminal - ANSWER: current carrying green insulated conductor that powers the indoor fan
circuit from thermostat.
24 volts - ANSWER: With the fan switch on "auto" and test probes on R and G terminals, the
voltage reading should be:
r and g - ANSWER: If the fan is in the "on" position but does not come on, a test to find out
whether you have a defective subbase, is to place a jumper between these two terminals
defective - ANSWER: When a system will not operate and a jumper is placed between terminals
R and G, and the fan starts, the subbase is
transformer - ANSWER: Non-starting indoor fan with a jumper between terminals R and G leads
the technician to search for the problem starting at the ________ or associated wiring.
subbase - ANSWER: Jumpering between terminals R and G, and finding that the fan does not
start usually means there is NO problem at the_______.
cooling circuit - ANSWER: Placing a jumper between terminals R and Y on the subbase is how
to energize the ______________
thermostat - ANSWER: If a cooling circuit runs (including compressor) only with a jumper, but
not by setting the thermostat to the cooling mode, the defective component is the
____________
heating circuit - ANSWER: Placing a jumper between terminals R and W on the subbase is how
to energize the _____________
thermostat - ANSWER: If a heating circuit runs only with a jumper, but not by setting the
thermostat to the heating mode, the defective component is the ____________
capped taped - ANSWER: To prevent the possibility of a short, unused wire leads on a multi-tap
transformer should be ______ and _______.
24 volts - ANSWER: When voltage is applied to the primary transformer winding, the secondary
should read ____________
resistance - ANSWER: A transformer that does not have a low voltage reading at the secondary
winding must be disconnected from the system and tested for ____________.
open - ANSWER: If the resistance reading across the secondary transformer winding is infinity,
the winding is ______ and needs replacement.