ICC Masonry
Comprehensive Resource To Help You Ace 2026-2027 Exams
Includes Frequently Tested Questions With ELABORATED
100% Correct COMPLETE SOLUTIONS
Guaranteed Pass First Attempt!! Current Update!!
1. Windbreaks shall be used when the temp is below 25°F and the wind is .....
A. 8 mph or more
B. 10 mph or more
C. 12 mph or more
D. Greater than 15 mph - Correct Answer: Answer D. Greater than
15 mph
2. After the initial water has been introduced to the mix, mortar should be
used within .....
A. 30 minutes
B. 1 hour
C. 1-1/2 hour
D. 2-1/2 hour - Correct Answer: Answer D. 2-1/2 hour
3. A common CMU size is 6" x 8" x 16". The 8" refers to the .....
A. Width
B. Height
C. Length - Correct Answer: Answer. B. Height
,4. During hot weather conditions, newly constructed masonry shall be fog
sprayed until damp at least ..... times a day for ..... days
A. Twice a day for 3 days
B. Twice a day for 5 days
C. 3 times a day for 3 days
D. 3 times a day for 5 days - Correct Answer: Answer C. 3 times a day
for 3 days
5. When associated with masonry reinforcing steel, the "d" distance is defined
as the distance from ..... to the center of the reinforcing steel.
A. The inside of the face shell
B. The nearest reinforcing bar
C. The farthest face of the CMU
D. The centerline of an associated lap splice bar - Correct Answer:
Answer C. The farthest face of the CMU
6. When performing the Cone Penetrometer Test, the depth of penetration is
measured in .....
A. Meters
B. Millimeters
C. Centimeters
D. Inches - Correct Answer: Answer B. Millimeters
7. The recommended slump is necessary so that grout can flow .....
A. Without hydration
B. Completely surround the steel
C. Into the cracks
D. Without hydrostatic pressure - Correct Answer: Answer B.
Completely surround the steel
, 8. Maximum horizontal spacing of control joints should be .....
A. 45 to 60 feet
B. 30 to 45 feet
C. 25 to 30 feet
D. 20 to 30 feet - Correct Answer: Answer C. 25 to 30 feet
9. When high lift grouting, the full height of any section of wall should be
completed in one day, with no interruption between lifts greater than .....
A. One hour
B. Two hours
C. Three hours
D. Four hours - Correct Answer: Answer A. One hour
Expansion joints are used to provide for movement of a wall as it expands
and must contain incompressible material.
10.True or False - Correct Answer: Answer is False
11.Mortar projections in grout cells must not project more than ..... into a cell.
A. 0 inches
B. 1/4 inches
C. 1/2 inches
D. 1 inch - Correct Answer: Answer C. 1/2 inches
Comprehensive Resource To Help You Ace 2026-2027 Exams
Includes Frequently Tested Questions With ELABORATED
100% Correct COMPLETE SOLUTIONS
Guaranteed Pass First Attempt!! Current Update!!
1. Windbreaks shall be used when the temp is below 25°F and the wind is .....
A. 8 mph or more
B. 10 mph or more
C. 12 mph or more
D. Greater than 15 mph - Correct Answer: Answer D. Greater than
15 mph
2. After the initial water has been introduced to the mix, mortar should be
used within .....
A. 30 minutes
B. 1 hour
C. 1-1/2 hour
D. 2-1/2 hour - Correct Answer: Answer D. 2-1/2 hour
3. A common CMU size is 6" x 8" x 16". The 8" refers to the .....
A. Width
B. Height
C. Length - Correct Answer: Answer. B. Height
,4. During hot weather conditions, newly constructed masonry shall be fog
sprayed until damp at least ..... times a day for ..... days
A. Twice a day for 3 days
B. Twice a day for 5 days
C. 3 times a day for 3 days
D. 3 times a day for 5 days - Correct Answer: Answer C. 3 times a day
for 3 days
5. When associated with masonry reinforcing steel, the "d" distance is defined
as the distance from ..... to the center of the reinforcing steel.
A. The inside of the face shell
B. The nearest reinforcing bar
C. The farthest face of the CMU
D. The centerline of an associated lap splice bar - Correct Answer:
Answer C. The farthest face of the CMU
6. When performing the Cone Penetrometer Test, the depth of penetration is
measured in .....
A. Meters
B. Millimeters
C. Centimeters
D. Inches - Correct Answer: Answer B. Millimeters
7. The recommended slump is necessary so that grout can flow .....
A. Without hydration
B. Completely surround the steel
C. Into the cracks
D. Without hydrostatic pressure - Correct Answer: Answer B.
Completely surround the steel
, 8. Maximum horizontal spacing of control joints should be .....
A. 45 to 60 feet
B. 30 to 45 feet
C. 25 to 30 feet
D. 20 to 30 feet - Correct Answer: Answer C. 25 to 30 feet
9. When high lift grouting, the full height of any section of wall should be
completed in one day, with no interruption between lifts greater than .....
A. One hour
B. Two hours
C. Three hours
D. Four hours - Correct Answer: Answer A. One hour
Expansion joints are used to provide for movement of a wall as it expands
and must contain incompressible material.
10.True or False - Correct Answer: Answer is False
11.Mortar projections in grout cells must not project more than ..... into a cell.
A. 0 inches
B. 1/4 inches
C. 1/2 inches
D. 1 inch - Correct Answer: Answer C. 1/2 inches
