Docuflash

A ______ conveys a liquid. - correct answer Pump What are the two main categories of pumps? - correct answer Centrifugal and positive displacement Pumps at a constant capacity regardless of pressure. - correct answer Positive displacement Which pump does not see a decrease in flow with an increase in viscosity? - correct answer Positive displacement Name three designs of pump impellers. - correct answer Open, semi-closed, closed How does a centrifugal pump move liquid? - correct a...

If the seal was not properly aligned or there is excessive wear in some bearing or shaft______ wear tracks will be the indicator. - correct answer Unusual For removing hard to remove gasket materials found on sealing surfaces ______ is recommended. - correct answer sharpened brass putty knife Apprenticeship training is - correct answer Conducted on the job Charting alignment on a graph requires a chart that is divided into thousandths of an inch vertically for the indicator readings and...

MILLWRIGHT RIGGING & LIFTING EXAM 2024 100% CORRECT ANSWERS The breaking strength of rope is a. force needed to pull rope b. force needed to tear rope c. force needed to break the rope d. force needed to stretch rope - correct answer c. force needed to break the rope What are spreader beams used for? a. calculate loads b. use on heavy lods c. support loads during lifts d. support long loads during lifts - correct answer d. support long loads during lifts What are equalizer bea...

Which of the following best describes a free flow control valve? A) It is the simplest form of directional control allowing flow in one direction only B) They are used to prevent a load suspended by a cylinder from free fall C) They operate actuators at different times D) They make a humming sound when activated E) They control the rate of fluid flow in a hydraulic circuit - correct answer E) They control the rate of fluid flow in a hydraulic circuit A lifter is a solid or hydraulic devi...

Which of the following best describes a free flow control valve? A) It is the simplest form of directional control allowing flow in one direction only B) They are used to prevent a load suspended by a cylinder from free fall C) They operate actuators at different times D) They make a humming sound when activated E) They control the rate of fluid flow in a hydraulic circuit - correct answer E) They control the rate of fluid flow in a hydraulic circuit A lifter is a solid or hydraulic devi...

MILLWRIGHT NCCER EXAM 2024 WITH 100% CORRECT ANSWERS

which of the following tools would be used on a polished steel assembly. - correct answer strap wrench The type of wrench designed for use on a specific part is the ______ wrench. - correct answer Spanner what kind of tool do you use for packing. - correct answer Packing gauge Can you use a Tubing Cutters tool to cut steel pipe too. - correct answer False A honing stone is used to. - correct answer Sharpen Tools The tool used to line up holes in flanges is a. - correct answer Drif...

The best method of alignment to apply when shafts can not be axially secured is? - correct answer cross dialing Sag corrections in dial setting are applied only to? - correct answer vertical rim readings limitations in use of cross dialing methods include substantial brackets for long spans, less accuracy over short spans, and? - correct answer both shafts must turn optalign plus alignment requires the transducer assembly be mounted upon the? - correct answer primary equipment depend...

On a pedestal grinder, the gap between the grinding wheel and work rest should not exceed: - correct answer 1/8 inch The kind of abrasive material used in grinding wheels for general purpose applications is: - correct answer aluminum oxide A blotter is used on a grinding wheel to: - correct answer protect the flanges from the abrasize grit, display information about the wheel and compensate for the uneven surfaces on the wheel Flanges should at least be: - correct answer 1/3 the diamete...

1. How is efficiency found? A) output over input B) input over output C) output times input times 100 D) output times input divided by hp - correct answer A) Output over input 2. What is the maximum capacity in kg of a heavy duty ladder? A) 136 B) 113 C) 102 D) 91 - correct answer B)113 . Worn ring grooves on an engine piston will cause: A) the rings to rock back and forth. B) combustion gases to blow by the rings into the crankshaft. C) oil consumption. D) all of the above...

MILLWRIGHT EXAM 2024 WITH 100 % CORRECT ANSWERS 1. When the downward force at C2 is 100 lb and D2 = 2.5 inches, the upward force at C1 will be ________lb if D1 = 4 inches. A. 160 B. 256 C. 384 D. 240 - correct answer A. 160 x/12.56 sq in = 100 lbs/7.85 sq in x = (100lbs/7.85 sq in)12.56 x = 16

1. When the downward force at C2 is 100 lb and D2 = 2.5 inches, the upward force at C1 will be ________lb if D1 = 4 inches. A. 160 B. 256 C. 384 D. 240 - correct answer A. 160 x/12.56 sq in = 100 lbs/7.85 sq in x = (100lbs/7.85 sq in)12.56 x = 160 lbs 2. Add the following decimals and express the answer to three decimal places. 0.4789 + 3.125 + 9.656 A. 13.26 B. 13.3 C. 13.259 D. 13.2599 - correct answer C. 13.259 3. What are common materials used as electrical conductor...

MILLWRIGHT EXAM 1 2024 WITH 100% CORRECT ANSWERS Compared to fibre core, IWRC tends to be _______ resilient and less capable of absorbing shock loads a. more b. less c. equally d. slightly more - correct answer b. less What rope is considered to be a standard wire a. Lang lay b. right regular lay c. left regular lay d. performing lay - correct answer b. right regular lay What safety factor is used for elevators? a. 30-

MIE 330 TEST 1 (CHAPTERS 1-4) EXAM 2024 WITH 100% CORRECT ANSWERS Human Resource Management (chapter 1) - correct answer The policies, Practices, and systems that influence employees' behavior, attitudes, and performance Human Capital (Chapter 1) - correct answer An organization's employees, described in terms of their training, experience, judgement, intelligence, relationships, and insight. HR Responsibilities (10) (Chapter 1) - correct answer Analysis and job design Recruitm...

MIE 330 FINAL EXAM 2024 WITH 100% CORRECT ANSWERS Job Evaluation - correct answer An administrative procedure for measuring the relative internal worth of the organization's jobs. Pay Ranges - correct answer A set of possible pay rates defined by a minimum, maximum, and midpoint of pay for employees holding a particular job or a job within a particular pay grade. Compa-Ratio - correct answer The ratio of average pay to the midpoint of the pay range. -If the average equals the midpo...

MIE 330 FINAL EXAM 2024 WITH 100% CORRECT ANSWERS What are the three characteristics of an employer's side on pay? - correct answer 1. Powerful tool for meeting org goals 2. Impacts employees attitudes and behaviors 3. Influences the kinds of people attracted to/remain with the org What are the two characteristics of an employee's side on pay? - correct answer 1. Care about fairness 2. Attach great importance on pay decisions when evaluating relationships with employers Pay is a

MIE 330 EXAM 1 2024 WITH 100% CORRECT ANSWERS Human Resource Management (HRM) - correct answer The policies, practices, and systems that influence employees o Behavior o Attitudes o Performance Employees and customers tend to be more satisfied when... - correct answer o the companies tend to... Be more innovative Have greater productivity Develop a more favorable reputation in the community Human capital - correct answer • an organization's employees described in terms of the...

MICHIGAN MPJE EXAM 2024 WITH 100% CORRECT ANSWERS Dispensing opioid antagonists - what is required and what information shall be submitted - correct answer 1. Pharmacies must register w/ department & pharmacists must be trained 2. Submit QUARTERLY: # opioids antagonists dispensed under standing order, # dispensed with rx, # of each type of formulation dispensed WITHOUT PT IDENTIFIERS! 3. Pharmacists shall provide educational material to eligible individuals and resources for treatment se...

MICHIGAN MPJE EXAM 2024 WITH 100% CORRECT ANSWERS Which prescription type is good for 12 months - correct answer Noncontrolled and schedule 5 Which prescription type is good for 6 months - correct answer Schedule 3-4 Which prescription type is good for 90 days - correct answer Schedule 2 Max refills for non control - correct answer 11 Max refills for schedule 5 - correct answer 11 Max refills for schedule 3-4 - correct answer 5 Max refills for schedule 2 - correct answer N...

MIC 205 FINAL EXAM 2024 WITH 100% CORRECT ANSWERS 3 characteristics of plasma B cells - correct answer produced during B call proliferation secrets a complementary molecule specific to the antigenic short-lived (days) 5 parts of an antibody: - correct answer polypeptides covalent bonds heavy and small chains antigen binding sites (2) Fc region A molecule or fragment that triggers a specific immune response is an: - correct answer antigen