TESTSOLVER9 STORE

Longitudinal (Roll), Lateral (pitch), Vertical (yaw) - Answer The three axes of an airplane are: Longitudinal - Answer The ailerons rotate an airplane about its _______ axis. Lateral - Answer The elevators rotate an airplane about its _____ axis. Vertical - Answer The rudder will rotate an aircraft about its _____ axis. Rudder - Answer The _____ is used to overcome the effects of aileron drag. Static, Dynamic - Answer The two types of stability ...

Metal in which iron is the chief ingredient is called - Answer Ferrous Metal Low carbon steel contains less than - Answer 30 hundredths of one percent carbon High carbon steel contains above - Answer 50 hundredths of one percent carbon The ability to withstand tension is called - Answer Tensile Strength The ability of a metal to resist deformation is called - Answer Yield Strength The ability of a metal to resist cutting, penetration, or abrasion is -...

What is the function of a vortex generator? - Answer It is designed to delay or prevent separation of the boundary layer. What are the 3 axis of an airplane? - Answer Longitudinal, Lateral, and Vertical. What are the 3 primary flight controls? - Answer Ailerons, elevator, and rudder Name several types of secondary flight controls and describe their general purpose. - Answer Secondary flight controls consist of various types of trim tabs such as balance tabs, anti...

What are two reasons weight and balance control are important in an aircraft? - Answer Safety of flight and most efficient operation of an aircraft. Where is the center of gravity for most airplanes located in relation to the center of lift? - Answer The CG is normally ahead of the center of lift. What is meant by the datum that is used for weight and balance computations? - Answer It is a readily identified reference chosen by the aircraft manufacturer from which all lon...

1 Exam (elaborations) Heavy Equipment Technician Test Questions and All Correct/Verified Answers 2025-2026 Updated. 2 Exam (elaborations) Heavy Duty Technician Practice Exam And 100% Correct Answers 2025-2026 Updated. 3 Exam (elaborations) 310T- Air System and Brakes Questions and All Correct Answers 2025-2026 Updated.

What is an example of controlling a hazard through engineering controls? - Answer A substitution of equipment to remove the hazard Paraphrasing while listening to a speaker's message reassures the speaker that you are listening to them. (T/F) - Answer True A pressure gauge is installed with a shut-off valve and a tee to the main line. When is the shut-off valve opened? - Answer It is opened only when a pressure reading is taken A technician will find that a ________...

When installing camshaft gears where is it critical that the timing marks will be? - Answer They must face away from the camshaft If a Timing Chain in an engine has a chain deflection of how much of an inch it should be replaced? - Answer If it has a deflection of 0.50 of an inch What is the pitch of a metric micrometer? - Answer 0.5 mm A bio-degradable fluid must be able to have what percent of the base fluid broken down in a certain period of time? - Answer 70 ...

1. What will cause air to leak out of the relay valve with the park brake released and the service brake not applied? a. Ruptured service brake diaphragm. b. Ruptured Park/Emergency brake diaphragm. c. Faulty secondary reservoir blow-off valve. d. Parking/Emergency brake chamber pushrod seal leak. - Answer d. Parking/Emergency brake chamber pushrod seal leak. 2. What will cause the wet tank air pressure to leak down overnight? a. A faulty air governor valve. b. A faulty one-way c...

Which of the following tools can be used to cut new external threads?! A die A thread pitch gauge A tap A thread chaser - Answer A die During a PM inspection a broken radiator fan shroud is noticed. Which of the following could cause this damage?! Loose fan belts A failed fan hub clutch A broken engine mount An out of balance fan assembly - Answer A broken engine mount During a PM inspection the steering wheel binds when turned. What could cause this condition?!...

Technician A says that EUIs are better than previous injectors because they have no injection lag caused by swelling pump lines and delivery valves. Technician B says that the use of electromagnetic solenoids by unit injectors produces injection delay. Who is correct? a. Technician A b. Technician B c. Both Technician A and Technician B d. Neither Technician A nor Technician B - Answer b. Technician B Technician A says that when setting unit injector adjustments during replacement, ...

1. When trouble shooting an electrical engine or transmission, what else might be require? a. Test lamp b. Break out box c. Continuity tester d. Ohm meter - Answer b. break out box 2. An electronically equipped vehicle over heats, the engine fan will no engage upon engine ECM request. What is likely the issue? a. Relay contacts burnt b. Open in the relay c. Solenoid open-circuit d. Solenoid seized - Answer b. open in the relay 3. When performing a test on the stator, t...

What is the ratio between exhaust temperatures to air intake temperature a) 2:1 b) 4:1 c) 3:1 d) 1:1 - Answer c) 3:1 JWACs are capable of reducing air intake temperatures by ____________. a) 75°F b) 50°F c) 100°F d) 125°F - Answer c) 100°F ATAAC system cooling is affected by which variable? a) Surface area b) Road speed c) Ambient temperature d) All are correct - Answer d) All are correct There should not be a pressure drop of more than _______, ...

In Ontario, what is the acceptable variance from a written estimate? - Answer 10% Which part of a repair order authorizes the shop to proceed with the repairs - Answer The customer’s signature What is the first step in a logical diagnostic approach? - Answer Verify the problem exists What is an undesirable substance that may result from a service operation? - Answer Hazardous waste High concentration of undesirable vapours, gases or solids in the form of du...

1. What procedure should be followed before using a bench grinder? a) Dress stone and set rest with minimum clearance of 3 mm (1/8"). b) Dress stone and set rest with maximum clearance of 1.6 mm (1/16"). c) Set rest with minimum clearance of 3 mm (1/8") and dress stone. d) Set rest with maximum clearance of 1.6 mm (1/16") and dress stone. - Answer b) Dress stone and set rest with maximum clearance of 1.6 mm (1/16"). 2. What should be inspected on a chain sling before ...

1. Which of the following clutch components is a driven member?! a. clutch cover b. clutch friction disc c. intermediate plate d. pressure plate - Answer b. clutch friction disc 2. Which of the following is not a part of the clutch cover assembly?! a. pressure spring b. release lever c. pressure plate d. adapter ring - Answer d. adapter ring 3. Which of the following clutch components is splined to the input shaft of the transmission?! a. clutch friction disc b. press...

1. Which of the following accurately describes engine displacement?! a. Total piston swept volume b. Mean effective pressure c. Peak horsepower d. Peak torque - Answer a. Total piston swept volume 2. Engine breathing in the two-stroke cycle is usually referred to as?! a. Inertial b. Scavenging c. Exhaust displacement - Answer b. Scavenging 3. The tendency of an object in motion to want to stay in motion is known as?! a. Kinetic energy b. Dynamic friction c. Inertia d...

1. The shift lever vibrates and produces a noise that is audible from the transmission only while under deceleration. What is the likely cause? a. Brinelled U-joints b. Slip joint lacks lubrication c. Defective clutch d. Driveline out of phase - Answer b. Slip jount lacks lubrication 2. The surface contact area of a ring & pinion gearset is "centered" upon the gear teeth, but the gear-contact is too close to the top-land. What procedure is required in order to provide the c...

1 Exam (elaborations) Product Receiving - (CLT) Chapter 1 Questions with Solved Solutions. 2 Exam (elaborations) Logistics Mid-Level Technician Study Guide Questions with Accurate Answers 2025-2026 Updated. 3 Exam (elaborations) CLT Practice Final Exam with Guaranteed Pass Solutions 2025-2026 Updated.

Item - Answer A specific SKU Line - Answer Multiple requirements for a particular SKU, i.e, the number of items of a particular SKU How would the order cycle process be without an automated decision-making system? - Answer The process could take weeks as the order is shuffled among sales, customer service, logistics and accounting departments. The paper trail may be haphazard and error prone. What is a SKU? - Answer stock keeping unit- pronounced skew- A SKU is a...

Which of the following governing bodies has 153 member countries that represent 95% of total trade? - Answer World Trade Organization Which of the following documents list items in a vehicle's cargo and includes the customer's address, invoice numbers, package weights to ensure that the right packages end up on the correct trailer? - Answer Shipping manifest Which of the following terminology refers to products produced in one country and sold in a foreign country? - Answ...