Paul Marks Library

Texas Plumbing Master Exam| Questions with correct Answers| Latest Update air gap the vertical distance between the opening of the water supply and the flood level rim of a receptacle branch any part of the piping system other than a main, riser or stack Branch vent A vent connecting one or more individual vents with a vent stack or stack vent Building Drain is the lowest part of the drainage system which receives waste from soil and waste pipes and connects to the building sewer Build...

Journeyman and Master Plumbing Exam Question Bank| Actual Exam Questions and 100% Correct Answers| Latest Update What degree is used for isometric drawings? 60 degrees What is the recommended minimum of minutes for chlorine water management? 20-30 minutes When you need to repair a single handle lavatory faucet, what needs to be replaced? O ring Galvanic corrosion of water supply piping can occur where steel pipe is joined to a dissimilar metal pipe Whenever necessary to make an inspect...

Pipefitting year one practice exam| Already Graded 100% Correctly| Newest ! Class D, poisonous and infectious material What type of material does the following WHMIS symbol represent? What is the sequence of events when an electrical shock occurs? 1- eliminate the danger. 2- report the incident. 3- prevent further injury. 4- remove the victim. 5- send for qualified help. 4 3 5 1 2 What class of CSA non-conducting headwear is designed to provide protection against impact and penetration...

Pipefitter Star Exam Part 2| Answered 100% correctly| Latest ! Lockout/Tagout Standard procedure used to safely de-energize equipment on circuits before they are worked on: Fall hazards, Electrical hazards, Caught in, Struck by Four focus inspectioin OSHA compliance officers look for: Plane End Square Cut (PESC) Thread and Coupling (T&C) Thread Both Ends (TBE) Steel pipe is supplied with the following end finish: Start/Stop, Regulate/Throttle, Relief, Reduce Four principle functions of...

Pipefitter Star Exam Part 1| Questions and correct answers| Latest Violent flashing and collapsing of vapor bubbles in a centrifugal pump is called. Cavitation Device that controls the pressure in a low pressure steam boiler Pressuretrol Function of an evaporator Absorb heat from the system Metal which has a high iron content ferrous Why should the angle between the leg of a swing and the load never be less than 30 degrees? More stress loads are applied on the sling What are two kind...

Pipefitter Star Exam 2025| Questions and 100% Correct Answers| Latest ! What type of knot or hitch can be used for lifting a length of small-bore pipe vertically? a. bowline b. clove hitch c. granny knot d. sheepshank b. clove hitch What type of crane signal includes pointing the index finger to the ground and moving it in a circular motion? a. hoist b. lower c. boom down d. boom out b. lower What type of hand signal includes pointing the thumb down to the side of the body? a. lowe...

Pipefitter NCCER Test | Already Graded 100% Pass| Newest ! Convert 1/4 to its decimal equivalent. A) .01 B) .25 C) 0.4 D) 0.5 B Piping that is field-routed to a pump must be supported A) Off the pump suction B) Diagonally C) Independently D) Off the pump discharge C What is used when lighting a cutting torch ? A) Striker B) Cigarette lighter C) Match D) Any open flame A Where is specific information needed to install piping and associated items found ? A) Reliability network ...

pipe fitter test| Answered 100% correctly| Newest ! What does TE in TE-601 stand for? temperature element what does B.T.U stand for? British Thermal Unit what is the boiling point of water? 212*F What is 3.1416? Pi what is the circumference of a 15" pipe? (to the nearest tenth0 47" 4" in the hundredths of a foot is? .33 what is the take off for a 4" x 3" LR reducing 90* ell? 6" on isometric drawings what does RFWN mean? raised face weld neck what does the Pi in...

Pipefitter Star Exam| 800+ Questions with correct Answers| Already Graded 100% Pass| Latest ! What causes 90% of all construction injuries and deaths and are used to help OSHA inspectors improve their effectiveness? Focus Hazards What is the minimum safe working distance for overhead power lines? 10 feet What is the standard procedure used to safely de-energize equipment on circuits before they are worked on? Lockout/Tagout Which of the following is not true about Material Safety Data She...

ICLA Standard IV Exam Questions and correct answers Latest Update Writing the process of encoding into syntactic (grammatical) structures an organized set of ideas which are semantically (meaning) related Writing Process order of steps in creating a piece of writing: prewriting, writing/drafting, revising, editing, publishing Prewriting First step in the writing process; the writer generates ideas Drafting To draw the outlines or plan of; sketch; emphasize content rather than mechanics ...