Millwright Alberta Period 3 FINAL EXAM STUDY GUIDE 2025/2026 COMPLETE QUESTIONS BANK AND CORRECT DETAILED ANSWERS WITH RATIONALES || 100% GUARANTEED PASS <LATEST VERSION>

Millwright Alberta Period 3 FINAL EXAM STUDY GUIDE 2025/2026 COMPLETE QUESTIONS BANK AND CORRECT DETAILED ANSWERS WITH RATIONALES || 100% GUARANTEED PASS &lt;LATEST VERSION&gt; What is a ball peen hammer used for? - ANSWER Riveting # teeth on a hacksaw for cutting a 1" aluminum shaft? - ANSWER 14 pitch blade a coarse pitch blade is best for - ANSWER soft material a fine pitch blade is best for - ANSWER hard material which file has the smoothest cut? - ANSWER Single cut file Circle Snips have a - ANSWER Convex cutting edge what die is used to cut an undersized thread? - ANSWER Adjustable screw plate die how can you stop pinning on a file - ANSWER chalk the file face what surface is used for lapping of a flat steel part? - ANSWER smooth cast iron plate what is the main difference between hand taps in a standard set? - ANSWER the taper 3 types of hand taps in a standard set - ANSWER taper, plug and bottoming which hand tap has no taper - ANSWER bottoming tap Most effective type of hearing protection? - ANSWER plugs and earmuffs what is the highest safest step on a ladder - ANSWER don't use the top 2 rungs fire extinguisher class A, B, C, D - ANSWER Wood, Flammable liquids, electrical, combustible metals when is a whimis label not required? - ANSWER when a controlled product is used immediately scaffolding cross brace name - ANSWER end or transverse brace intentional difference between mating parts? - ANSWER allowance the amount of variation between parts - ANSWER tolerance gap or space between mating parts - ANSWER clearance what is used with an outside caliper to measure a shaft? - ANSWER a steel rule vernier caliper smallest measurement? - ANSWER one thou if an inch 0.001" or 0.20mm parallel misalignment + angular misalignment - ANSWER combination misalignment how to measure a small hole? - ANSWER small hole gauge and outside micrometer Reading a Vernier bevel protractor in what ? - ANSWER main scale is degrees and vernier scale is minutes indicates every 5 minutes = 1/20 of a degree What has to be aligned during machine installation - ANSWER Centerlines what's a datum line - ANSWER standard of comparison or point of reference most important point prior to a layout is - ANSWER reference line/datum line smallest dimension on a steel rule - ANSWER 1/64th accuracy of a vernier caliper - ANSWER 0.01mm or 0.001" (one thou) What do you use to set the axis of the threading tool at a right angle to the axis of the workpiece? - ANSWER thread centre gauge (fishtail) sensitive tool that is used to measure the depth of small holes and bores? - ANSWER depth micrometer (scale runs opposite to most micrometers) smallest measurement on a vernier metric micrometer - ANSWER 0.001 mm Type of wrench used on a polished or smooth surface? - ANSWER Strap Wrench Puller used for removing Bearing? - ANSWER Pressure Screw Puller 4 types of Pullers? - ANSWER pressure screw puller Hydraulic puller Slide hammer puller Bar-style puller maximum cut for a hand reamer - ANSWER .005" What are Broaches used for? - ANSWER cutting keyway seat with an arbour press. Hand broaching proceeds ______ " each tooth - ANSWER 0.003" what is the highest safest step on a ladder - ANSWER don't use the top 2 rungs when is a whimis label not required? - ANSWER when a controlled product is used immediately intentional difference between mating parts? - ANSWER allowance the amount of variation between parts - ANSWER tolerance gap or space between mating parts - ANSWER clearance what is used with an outside caliper to measure a shaft? - ANSWER a steel rule vernier caliper smallest measurement? - ANSWER one thou if an inch 0.001" or 0.20mm parallel misalignment + angular misalignment - ANSWER combination misalignment how to measure a small hole? - ANSWER small hole gauge and outside micrometer Reading a Vernier bevel protractor in what ? - ANSWER main scale is degrees and vernier scale is minutes indicates every 5 minutes = 1/12 of a degree What has to be aligned during machine installation - ANSWER Centerlines what's a datum line - ANSWER standard of comparison or point of reference most important point prior to a layout is - ANSWER reference line/datum line smallest dimension on a steel rule - ANSWER 1/64th accuracy of a vernier caliper - ANSWER 0.01mm or 0.001" (one thou) What do you use to set the axis of the threading tool at a right angle to the axis of the workpiece? - ANSWER thread centre gauge (fishtail)