J-STD-001 EXAM QUESTIONS
WITH GUARANTEED ACCURATE
ANSWERS |2025\26 |COMPLETE
Who is responsible for identifying the assembly class? - ACCURATE
ANSWERS✔✔ User
What is a defect? - ACCURATE ANSWERS✔✔ A condition that may affect the
form, fit, or function of the item in the end use environment
Hardware found to not conform to the requirements of the standard shall be
classified as defects and dispositioned for: - ACCURATE ANSWERS✔✔
[D1D2D3]
There shall be no broken strands for wires used at a potential of 6kV or greater: -
ACCURATE ANSWERS✔✔ [D1D2D3]
A documented process control system shall be implemented for: - ACCURATE
ANSWERS✔✔ [N1N2D3]
The contract shall take precedence over this standard for: - ACCURATE
ANSWERS✔✔ [D1D2D3]
What is wire overlap? - ACCURATE ANSWERS✔✔ When a wire is wrapped
more than 360 and crosses over itself
, What is wire over wrap? - ACCURATE ANSWERS✔✔ When a wire is wrapped
more than 360 and remains in contact with the terminal
Manufacturers shall perform 100% inspection unless sampling inspection is
defined for: - ACCURATE ANSWERS✔✔ [N1D2D3]
Inspection of soldering and cleanliness shall be performed prior to conformal
coasting, staking, or encapsulation for: - ACCURATE ANSWERS✔✔ [N1D2D3]
Illumination at the surface of work stations should be at least what? - ACCURATE
ANSWERS✔✔ 1000 lux
What is the tolerance for magnification aids? - ACCURATE ANSWERS✔✔ +-
15%
Eating, drinking, smoking, e-cigs use shall be prohibited at the work station for: -
ACCURATE ANSWERS✔✔ [D1D2D3]
Manufacturer shall verify ESD is adequate when humidity falls below 30% for: -
ACCURATE ANSWERS✔✔ [N1D2D3]
Manufacturer shall establish an ESD control program for: - ACCURATE
ANSWERS✔✔ [D1D2D3]
What is J-STD-002? - ACCURATE ANSWERS✔✔ Solder-ability tests for
Component leads, terminations, lugs, wires, and terminals
WITH GUARANTEED ACCURATE
ANSWERS |2025\26 |COMPLETE
Who is responsible for identifying the assembly class? - ACCURATE
ANSWERS✔✔ User
What is a defect? - ACCURATE ANSWERS✔✔ A condition that may affect the
form, fit, or function of the item in the end use environment
Hardware found to not conform to the requirements of the standard shall be
classified as defects and dispositioned for: - ACCURATE ANSWERS✔✔
[D1D2D3]
There shall be no broken strands for wires used at a potential of 6kV or greater: -
ACCURATE ANSWERS✔✔ [D1D2D3]
A documented process control system shall be implemented for: - ACCURATE
ANSWERS✔✔ [N1N2D3]
The contract shall take precedence over this standard for: - ACCURATE
ANSWERS✔✔ [D1D2D3]
What is wire overlap? - ACCURATE ANSWERS✔✔ When a wire is wrapped
more than 360 and crosses over itself
, What is wire over wrap? - ACCURATE ANSWERS✔✔ When a wire is wrapped
more than 360 and remains in contact with the terminal
Manufacturers shall perform 100% inspection unless sampling inspection is
defined for: - ACCURATE ANSWERS✔✔ [N1D2D3]
Inspection of soldering and cleanliness shall be performed prior to conformal
coasting, staking, or encapsulation for: - ACCURATE ANSWERS✔✔ [N1D2D3]
Illumination at the surface of work stations should be at least what? - ACCURATE
ANSWERS✔✔ 1000 lux
What is the tolerance for magnification aids? - ACCURATE ANSWERS✔✔ +-
15%
Eating, drinking, smoking, e-cigs use shall be prohibited at the work station for: -
ACCURATE ANSWERS✔✔ [D1D2D3]
Manufacturer shall verify ESD is adequate when humidity falls below 30% for: -
ACCURATE ANSWERS✔✔ [N1D2D3]
Manufacturer shall establish an ESD control program for: - ACCURATE
ANSWERS✔✔ [D1D2D3]
What is J-STD-002? - ACCURATE ANSWERS✔✔ Solder-ability tests for
Component leads, terminations, lugs, wires, and terminals
