FAA Repairman Certificate – Light-Sport
Aircraft (LSA) Inspection – Weight-Shift
Control Exam Practice Test Questions And
Correct Answers (Verified Answers) Plus
Rationales 2026 Q&A | Instant Download
Pdf
1. What is the primary control used to change pitch in a weight-shift control
aircraft?
A. Rudder pedals
B. Flaps
C. Control bar movement forward or backward
D. Trim tab
Rationale: Pitch is controlled by shifting the center of gravity through
forward or backward control bar movement.
,2. Which FAA regulation governs the issuance of the Repairman Certificate
for Light-Sport Aircraft?
A. FAR Part 91
B. FAR Part 65, Subpart D
C. FAR Part 43
D. FAR Part 21
Rationale: FAR Part 65, Subpart D defines eligibility and privileges for
Repairman Certificates.
3. What must be included in an aircraft maintenance record after an
inspection?
A. Owner’s address
B. Description of work performed, date, and signature with certificate
number
C. Weather conditions during inspection
D. Aircraft flight hours only
Rationale: FAA regulations require date, work description, and certificate
details for traceability.
4. What does the term “LSA” stand for?
A. Light Service Aircraft
B. Limited Sport Airplane
C. Light-Sport Aircraft
,D. Light Special Aircraft
Rationale: LSA stands for Light-Sport Aircraft, defined under 14 CFR §1.1.
5. What is the maximum takeoff weight allowed for a weight-shift control
LSA?
A. 1,000 pounds
B. 1,320 pounds (600 kg)
C. 1,430 pounds
D. 1,500 pounds
Rationale: The FAA limits LSA maximum takeoff weight to 1,320 lbs for
landplanes.
6. What document must be reviewed before performing an annual condition
inspection?
A. Pilot logbook
B. Manufacturer’s maintenance manual
C. Aircraft sales brochure
D. Flight plan
Rationale: The manufacturer’s manual specifies the required procedures
and tolerances for inspection.
, 7. What is the purpose of a torque wrench?
A. To loosen bolts quickly
B. To measure bolt diameter
C. To tighten fasteners to a specific load
D. To remove rivets
Rationale: Torque wrenches apply precise force to avoid over-tightening or
under-tightening.
8. What must be done after completing a 100-hour inspection?
A. Nothing; it’s only recorded every 200 hours
B. Record the inspection in the maintenance logbook
C. Submit report to the FAA
D. Replace the airworthiness certificate
Rationale: FAA requires logbook documentation of every 100-hour
inspection performed.
9. What type of corrosion appears as white or gray powder on aluminum
surfaces?
A. Filiform corrosion
B. Surface corrosion
C. Intergranular corrosion
D. Galvanic corrosion
Aircraft (LSA) Inspection – Weight-Shift
Control Exam Practice Test Questions And
Correct Answers (Verified Answers) Plus
Rationales 2026 Q&A | Instant Download
1. What is the primary control used to change pitch in a weight-shift control
aircraft?
A. Rudder pedals
B. Flaps
C. Control bar movement forward or backward
D. Trim tab
Rationale: Pitch is controlled by shifting the center of gravity through
forward or backward control bar movement.
,2. Which FAA regulation governs the issuance of the Repairman Certificate
for Light-Sport Aircraft?
A. FAR Part 91
B. FAR Part 65, Subpart D
C. FAR Part 43
D. FAR Part 21
Rationale: FAR Part 65, Subpart D defines eligibility and privileges for
Repairman Certificates.
3. What must be included in an aircraft maintenance record after an
inspection?
A. Owner’s address
B. Description of work performed, date, and signature with certificate
number
C. Weather conditions during inspection
D. Aircraft flight hours only
Rationale: FAA regulations require date, work description, and certificate
details for traceability.
4. What does the term “LSA” stand for?
A. Light Service Aircraft
B. Limited Sport Airplane
C. Light-Sport Aircraft
,D. Light Special Aircraft
Rationale: LSA stands for Light-Sport Aircraft, defined under 14 CFR §1.1.
5. What is the maximum takeoff weight allowed for a weight-shift control
LSA?
A. 1,000 pounds
B. 1,320 pounds (600 kg)
C. 1,430 pounds
D. 1,500 pounds
Rationale: The FAA limits LSA maximum takeoff weight to 1,320 lbs for
landplanes.
6. What document must be reviewed before performing an annual condition
inspection?
A. Pilot logbook
B. Manufacturer’s maintenance manual
C. Aircraft sales brochure
D. Flight plan
Rationale: The manufacturer’s manual specifies the required procedures
and tolerances for inspection.
, 7. What is the purpose of a torque wrench?
A. To loosen bolts quickly
B. To measure bolt diameter
C. To tighten fasteners to a specific load
D. To remove rivets
Rationale: Torque wrenches apply precise force to avoid over-tightening or
under-tightening.
8. What must be done after completing a 100-hour inspection?
A. Nothing; it’s only recorded every 200 hours
B. Record the inspection in the maintenance logbook
C. Submit report to the FAA
D. Replace the airworthiness certificate
Rationale: FAA requires logbook documentation of every 100-hour
inspection performed.
9. What type of corrosion appears as white or gray powder on aluminum
surfaces?
A. Filiform corrosion
B. Surface corrosion
C. Intergranular corrosion
D. Galvanic corrosion
