Page 1 of 21
ICC VAPOR RECOVERY VT exam ALL
QUESTIONS AND VERIFIED SOLUTIONS
LATEST UPDATE THIS YEAR
QUESTION: On new construction, after July 1, 2004, Can you install an in-ground Spill Bucket? -
ANSWER-YES-When Piping is monitored and with VAC
QUESTION: According to Executive Order 201 - Healy P/V Valve should be torqued at -
ANSWER-20-50 ft-lbs
QUESTION: For a fire to burn, these (3) three primary elements must exist: - ANSWER-Fuel,
Oxygen, Ignition Source
QUESTION: When working with Electrical - Lock Out Tag Out procedures are under these
guidelines. - ANSWER-CAL-OSHA
QUESTION: Organization that certifies vapor recovery systems. - ANSWER-CARB or ARB
1
, Page 2 of 21
QUESTION: According to RP 500, a level II technician may NOT inspect this part. - ANSWER-
Replace VP 1000 Healy Pump
QUESTION: where hanging hardware repairs must be tracked. - ANSWER-GDF maintenance log
QUESTION: approved sealant when assembling a Phil-Tite Drop Tube. - ANSWER-JB-Kwik
QUESTION: Material direct bury OPW container sleeve shall be made of. - ANSWER-Stainless
steel
QUESTION: What P/V vent cap shall be tightened to. - ANSWER-20-50 ft lbs
QUESTION: From dispenser to manifold - 2" diameter vapor piping ( 2" ID) and From manifold
to tank - 3" diameter vapor piping (3" ID) - ANSWER-Vapor piping
2
, Page 3 of 21
QUESTION: What is the maximum run for vapor piping? - ANSWER-No maximum run
QUESTION: How you know a nozzle spout is bad. - ANSWER-'BAD O-rinqs
Type of sealant you should you use on a Phil-Tite Ball Float nipple: - ANSWER-Pipe dope
QUESTION: Number of open valves on the clean air separator: - ANSWER-One
QUESTION: You must be CERTIFIED by Healy to re-connect a Healy breakaway, True or False? -
ANSWER-False
QUESTION: The type of pressure gauge is recommended to test Healy Vac - ANSWER-SYSA
gauge measuring 0-100 WC
QUESTION: According to PEI RP 300, on a balance Stage II vapor recovery system nozzle, Vapors
typically flow in what direction of the coaxial hose? - ANSWER-The outside pathway
3
ICC VAPOR RECOVERY VT exam ALL
QUESTIONS AND VERIFIED SOLUTIONS
LATEST UPDATE THIS YEAR
QUESTION: On new construction, after July 1, 2004, Can you install an in-ground Spill Bucket? -
ANSWER-YES-When Piping is monitored and with VAC
QUESTION: According to Executive Order 201 - Healy P/V Valve should be torqued at -
ANSWER-20-50 ft-lbs
QUESTION: For a fire to burn, these (3) three primary elements must exist: - ANSWER-Fuel,
Oxygen, Ignition Source
QUESTION: When working with Electrical - Lock Out Tag Out procedures are under these
guidelines. - ANSWER-CAL-OSHA
QUESTION: Organization that certifies vapor recovery systems. - ANSWER-CARB or ARB
1
, Page 2 of 21
QUESTION: According to RP 500, a level II technician may NOT inspect this part. - ANSWER-
Replace VP 1000 Healy Pump
QUESTION: where hanging hardware repairs must be tracked. - ANSWER-GDF maintenance log
QUESTION: approved sealant when assembling a Phil-Tite Drop Tube. - ANSWER-JB-Kwik
QUESTION: Material direct bury OPW container sleeve shall be made of. - ANSWER-Stainless
steel
QUESTION: What P/V vent cap shall be tightened to. - ANSWER-20-50 ft lbs
QUESTION: From dispenser to manifold - 2" diameter vapor piping ( 2" ID) and From manifold
to tank - 3" diameter vapor piping (3" ID) - ANSWER-Vapor piping
2
, Page 3 of 21
QUESTION: What is the maximum run for vapor piping? - ANSWER-No maximum run
QUESTION: How you know a nozzle spout is bad. - ANSWER-'BAD O-rinqs
Type of sealant you should you use on a Phil-Tite Ball Float nipple: - ANSWER-Pipe dope
QUESTION: Number of open valves on the clean air separator: - ANSWER-One
QUESTION: You must be CERTIFIED by Healy to re-connect a Healy breakaway, True or False? -
ANSWER-False
QUESTION: The type of pressure gauge is recommended to test Healy Vac - ANSWER-SYSA
gauge measuring 0-100 WC
QUESTION: According to PEI RP 300, on a balance Stage II vapor recovery system nozzle, Vapors
typically flow in what direction of the coaxial hose? - ANSWER-The outside pathway
3
