South Carolina Manufactured Housing Retail
Salesperson Study Prep – Questions With A+
Solutions
Save
Terms in this set (176)
The Uniform Standards Code for Manufactured
Act
Housing Act.
The straps, cables, turnbuckles, chains, or other
devices of any kind including tensioning devices,
Anchoring Equipment
which are used to secure a manufactured home to
the ground or foundation.
A method of construction which when properly
Anchoring System designed and installed will resist overturning and
lateral movement of the manufactured home.
Means acceptable to the authority having
Approved
jurisdiction.
The organization, office, or individual responsible
Authority Having
for "approving" equipment, an installation, or a
Jurisdiction
procedure.
A person acting on behalf of a manufactured home
Authorized Official
retail dealer.
Board The South Carolina Manufactured Housing Board.
Includes a defect in the performance, construction,
components, or material of a manufactured home
Defect
that renders the home or any part of it not fit for the
ordinary use for which it was intended.
A tie intended to primarily resist horizontal or shear
Diagonal Tie forces and which may secondarily resist vertical,
uplift, and overturning forces.
, The Department of Labor, Licensing and Regulation
and the staff responsible for providing
Department
administrative support to the Manufactured Housing
Board.
One or more habitable rooms which are designed
Dwelling Unit to be occupied by one family with facilities for
living, sleeping, cooking, eating, and sanitation.
The part of the structural system which is normally
Frame (Main) used to transit accumulative design loads to the
support system.
A site built or site assembled system of stabilizing
devices which is:
1) capable of transferring design dead loads and
live loads required by Federal Regulations and other
design loads unique to the local home sites due to
winds, seismic, and water conditions, that are
Foundation
imposed by or upon the structure into the
underlying soil bedrock without failure
2) in frost susceptible areas, placed at an adequate
depth, or otherwise adequately protected, to
prevent frost damage
3) constructed of materials acceptable to the
authority having jurisdiction
A listed connector designed for connecting the
Gas Supply Connector
manufactured home to the gas supply source.
A device at the manufactured home stand designed
Ground Anchor to transfer manufactured home anchoring loads to
the ground.
A room or enclosed floor space arranged for living,
eating, food preparation, or sleeping purposes not
Habitable Room including bathrooms, toilet compartments,
laundries, pantries foyers, hallways, and other
accessory spaces.
, A manufactured home which meets the wind design
load requirements for Zone II in Subpart D, Section
Hurricane Resistive
3280-305(c) (2) of the Federal Standard or the
Manufactured Home
applicable hurricane resistive design requirements
of the Standard of Manufactured Homes.
A hazard that presents an imminent and
Imminent Safety Hazard
unreasonable risk of death or severe personal injury.
A person employed by the Department as being
qualified to adequately inspect the construction,
electrical installations and mechanical installations
Inspector
of manufactured homes, as well as the installation,
tie downs, blocking, and sewer connections of new
manufactured homes.
The installation of operations performed at the
occupancy site which render a manufactured home
fit for habitation, Such operations include, but are
Install/Installed
not limited to, positioning, blocking, leveling,
supporting, tying down, connecting utility systems,
and assembling multiple or expandable units.
The equipment or materials to which has been
attached a label, symbol, or other identifying mark
of an organization acceptable to the authority
having jurisdiction and concerned with product
Labled evaluation, that maintains periodic inspection of
production of labeled equipment or materials, and
by whose labeling the manufacturer indicates
compliance with appropriate standards or
performance in a specified manner.
The equipment or materials included in a list
published by an organization acceptable to the
authority having jurisdiction and concerned with
product evaluation, that maintains periodic
Listed inspection of production of labeled equipment or
materials and whose listing states either that the
equipment or materials meets appropriate
standards or has been tested and found suitable for
use in a specified manner.
Salesperson Study Prep – Questions With A+
Solutions
Save
Terms in this set (176)
The Uniform Standards Code for Manufactured
Act
Housing Act.
The straps, cables, turnbuckles, chains, or other
devices of any kind including tensioning devices,
Anchoring Equipment
which are used to secure a manufactured home to
the ground or foundation.
A method of construction which when properly
Anchoring System designed and installed will resist overturning and
lateral movement of the manufactured home.
Means acceptable to the authority having
Approved
jurisdiction.
The organization, office, or individual responsible
Authority Having
for "approving" equipment, an installation, or a
Jurisdiction
procedure.
A person acting on behalf of a manufactured home
Authorized Official
retail dealer.
Board The South Carolina Manufactured Housing Board.
Includes a defect in the performance, construction,
components, or material of a manufactured home
Defect
that renders the home or any part of it not fit for the
ordinary use for which it was intended.
A tie intended to primarily resist horizontal or shear
Diagonal Tie forces and which may secondarily resist vertical,
uplift, and overturning forces.
, The Department of Labor, Licensing and Regulation
and the staff responsible for providing
Department
administrative support to the Manufactured Housing
Board.
One or more habitable rooms which are designed
Dwelling Unit to be occupied by one family with facilities for
living, sleeping, cooking, eating, and sanitation.
The part of the structural system which is normally
Frame (Main) used to transit accumulative design loads to the
support system.
A site built or site assembled system of stabilizing
devices which is:
1) capable of transferring design dead loads and
live loads required by Federal Regulations and other
design loads unique to the local home sites due to
winds, seismic, and water conditions, that are
Foundation
imposed by or upon the structure into the
underlying soil bedrock without failure
2) in frost susceptible areas, placed at an adequate
depth, or otherwise adequately protected, to
prevent frost damage
3) constructed of materials acceptable to the
authority having jurisdiction
A listed connector designed for connecting the
Gas Supply Connector
manufactured home to the gas supply source.
A device at the manufactured home stand designed
Ground Anchor to transfer manufactured home anchoring loads to
the ground.
A room or enclosed floor space arranged for living,
eating, food preparation, or sleeping purposes not
Habitable Room including bathrooms, toilet compartments,
laundries, pantries foyers, hallways, and other
accessory spaces.
, A manufactured home which meets the wind design
load requirements for Zone II in Subpart D, Section
Hurricane Resistive
3280-305(c) (2) of the Federal Standard or the
Manufactured Home
applicable hurricane resistive design requirements
of the Standard of Manufactured Homes.
A hazard that presents an imminent and
Imminent Safety Hazard
unreasonable risk of death or severe personal injury.
A person employed by the Department as being
qualified to adequately inspect the construction,
electrical installations and mechanical installations
Inspector
of manufactured homes, as well as the installation,
tie downs, blocking, and sewer connections of new
manufactured homes.
The installation of operations performed at the
occupancy site which render a manufactured home
fit for habitation, Such operations include, but are
Install/Installed
not limited to, positioning, blocking, leveling,
supporting, tying down, connecting utility systems,
and assembling multiple or expandable units.
The equipment or materials to which has been
attached a label, symbol, or other identifying mark
of an organization acceptable to the authority
having jurisdiction and concerned with product
Labled evaluation, that maintains periodic inspection of
production of labeled equipment or materials, and
by whose labeling the manufacturer indicates
compliance with appropriate standards or
performance in a specified manner.
The equipment or materials included in a list
published by an organization acceptable to the
authority having jurisdiction and concerned with
product evaluation, that maintains periodic
Listed inspection of production of labeled equipment or
materials and whose listing states either that the
equipment or materials meets appropriate
standards or has been tested and found suitable for
use in a specified manner.
