BICSI QUESTIONS WITH 100% ACCURATE
ANSWERS
Elastomeric module is what type of firestop system? - Accurate answers Mechanical
Which of the following is not part of an its installer function when working within a designated work
area? - Accurate answers Leave access floor panels, open ceiling systems, or trenches uncovered or
open
The standard that covers commercial building grounding and bonding requirements for
telecommunications is: - Accurate answers ANSI/TIA 607
The use of ___ reduces the risk of damage when attaching a bonding conductor to a metallic conduit -
Accurate answers Grounding bushings
Commonly installed in a workspace, what individual network connects to two or more devises through
the use of wireless? - Accurate answers Personal area network
What is the color code of pair 19 of a 25 pair cable? - Accurate answers Yellow-Brown
There are three forms of transmission methods to move information in the form of electrical or optical
signals from one point to another through a transport medium. What are the three? - Accurate
answers Simplex, half duplex and full duplex
What is the NEC article regulating communications systems? - Accurate answers 8
What is the number of required lanyards when leaving a lift? - Accurate answers 2
In testing your copper cabling, you get failing NEXT (near-end crosstalk) reports. One of your steps to
solve this problem should be: - Accurate answers Check the quality of the wire terminations in the
connector
The ITS installer should always seek the guidance of the __, when coming onto any project for the
minimum requirements for safe work and employee health at work - Accurate answers AHJ
When bonding equipment racks to the PBB or SBB, what is the minimum size ground wire you should
use? - Accurate answers 6 AWG
Ohm's Law is represented by ohms (R), amperage (I), and voltage (V). What is the formula for Ohm's
Law? - Accurate answers V=IXR
To avoid electromagnetic interference (EMI) on cabling, what is the recommended minimum separation
from electric motors and transformers? - Accurate answers 48"
When terminating Cat5e and higher, pair untwisting cannot exceed ____. - Accurate answers 0.5"
, Who should have the responsibility of selecting the type of pokethough (devise used for fire barriers)
device to be used? - Accurate answers ICT designer or structural engineer
What is the color code of the 7th pair of a 25 pair cable? - Accurate answers Red-Orange
If existing cables do not meet the requirements of the category/class of cabling, they must be; -
Accurate answers Replaced to meet new standards and or codes
A certification tester rated at a tester level IIIe Cat6a (class Ea) can test to a bandwidth up to; -
Accurate answers 500 MHz
Nothing impacts the design and construction of a telecommunications network more than ___; -
Accurate answers Codes, standards and regulations
What serves the purpose of increasing personnel safety and reduces the likelihood of fire hazards by
serving as the path for fault current? - Accurate answers Equipment grounding system
When using cable management, care should be used to select management that protects what? -
Accurate answers Minimum bend radius
NFPA 70, The National Electric Code, is revised every ____? - Accurate answers 3 years
The PPE that an in ITS installer is required to wear when performing a task depends on each of the
following except; - Accurate answers When driving the company van on a new construction job site
Its suggested that open top cable supports be used for no more than how many cables? - Accurate
answers 50
A common cabinet configuration providing increased efficiency in heat management is where? -
Accurate answers The hot sides of two cabinet rows face each other
A digital signal is represented by two bits; zero and one. Zero represents an "off" signal and one
represents an "on" signal. Each signal is referenced in voltage. What is the most commonly used "on" or
"off" (or plus/minus) voltage within the digital signal? - Accurate answers 3V
What is the recommended maximum value for the bonding resistance between the grounding electrode
and busbar? - Accurate answers 0.1 OHMS
What is the recommended Maximum length of a conduit segment between pulling points? - Accurate
answers 100'
Which of the following describes what fire safety must provide? - Accurate answers Containment,
detection, and suppression
If a pulling eye was not factory installed, a ___ can be used as a substitution. - Accurate answers
Pulling grip
ANSWERS
Elastomeric module is what type of firestop system? - Accurate answers Mechanical
Which of the following is not part of an its installer function when working within a designated work
area? - Accurate answers Leave access floor panels, open ceiling systems, or trenches uncovered or
open
The standard that covers commercial building grounding and bonding requirements for
telecommunications is: - Accurate answers ANSI/TIA 607
The use of ___ reduces the risk of damage when attaching a bonding conductor to a metallic conduit -
Accurate answers Grounding bushings
Commonly installed in a workspace, what individual network connects to two or more devises through
the use of wireless? - Accurate answers Personal area network
What is the color code of pair 19 of a 25 pair cable? - Accurate answers Yellow-Brown
There are three forms of transmission methods to move information in the form of electrical or optical
signals from one point to another through a transport medium. What are the three? - Accurate
answers Simplex, half duplex and full duplex
What is the NEC article regulating communications systems? - Accurate answers 8
What is the number of required lanyards when leaving a lift? - Accurate answers 2
In testing your copper cabling, you get failing NEXT (near-end crosstalk) reports. One of your steps to
solve this problem should be: - Accurate answers Check the quality of the wire terminations in the
connector
The ITS installer should always seek the guidance of the __, when coming onto any project for the
minimum requirements for safe work and employee health at work - Accurate answers AHJ
When bonding equipment racks to the PBB or SBB, what is the minimum size ground wire you should
use? - Accurate answers 6 AWG
Ohm's Law is represented by ohms (R), amperage (I), and voltage (V). What is the formula for Ohm's
Law? - Accurate answers V=IXR
To avoid electromagnetic interference (EMI) on cabling, what is the recommended minimum separation
from electric motors and transformers? - Accurate answers 48"
When terminating Cat5e and higher, pair untwisting cannot exceed ____. - Accurate answers 0.5"
, Who should have the responsibility of selecting the type of pokethough (devise used for fire barriers)
device to be used? - Accurate answers ICT designer or structural engineer
What is the color code of the 7th pair of a 25 pair cable? - Accurate answers Red-Orange
If existing cables do not meet the requirements of the category/class of cabling, they must be; -
Accurate answers Replaced to meet new standards and or codes
A certification tester rated at a tester level IIIe Cat6a (class Ea) can test to a bandwidth up to; -
Accurate answers 500 MHz
Nothing impacts the design and construction of a telecommunications network more than ___; -
Accurate answers Codes, standards and regulations
What serves the purpose of increasing personnel safety and reduces the likelihood of fire hazards by
serving as the path for fault current? - Accurate answers Equipment grounding system
When using cable management, care should be used to select management that protects what? -
Accurate answers Minimum bend radius
NFPA 70, The National Electric Code, is revised every ____? - Accurate answers 3 years
The PPE that an in ITS installer is required to wear when performing a task depends on each of the
following except; - Accurate answers When driving the company van on a new construction job site
Its suggested that open top cable supports be used for no more than how many cables? - Accurate
answers 50
A common cabinet configuration providing increased efficiency in heat management is where? -
Accurate answers The hot sides of two cabinet rows face each other
A digital signal is represented by two bits; zero and one. Zero represents an "off" signal and one
represents an "on" signal. Each signal is referenced in voltage. What is the most commonly used "on" or
"off" (or plus/minus) voltage within the digital signal? - Accurate answers 3V
What is the recommended maximum value for the bonding resistance between the grounding electrode
and busbar? - Accurate answers 0.1 OHMS
What is the recommended Maximum length of a conduit segment between pulling points? - Accurate
answers 100'
Which of the following describes what fire safety must provide? - Accurate answers Containment,
detection, and suppression
If a pulling eye was not factory installed, a ___ can be used as a substitution. - Accurate answers
Pulling grip
