CWB Level 1 Weld Symbols exam questions and 100% correct answers 2025

CWB Level 1 Weld Symbols
A weld symbol for a fillet weld has the vertical line to the left of the symbol. (True/False) - ✔✔
correct answer true



Arrow side significance will have the weld symbol on the top of the reference line. (True/False) - ✔✔
correct answer false



The tail of a welding symbol is optional. (True/False) - ✔✔ correct answer true



ISO 2553 System A symbolic representation consists of one solid and one dashed reference line in
parallel. (True/False) - ✔✔ correct answer true



When using a combination of weld symbols, the order of progression starts closest to the reference
line? (True/False) - ✔✔ correct answer true



What is the meaning of a black flag at the intersect of the reference line and the arrow line
orientated on the top side of a welding symbol? (Multiple choice)

Question 9 options:A) Inspection required in the field.B) Fillet weld to be completed in the field.C)
Field weld on the other side of the joint.D) Weld to be completed in the field. - ✔✔ correct answer



A weld symbol provides the necessary information to complete the joint preparation. (True/False) -
✔✔ correct answer false



What information can a weld symbol NOT provide? (Multiple choice)

Question 11 options:A) Joint preparation and geometry.B) Weld size and length.C) Bolt hole
locations.D) Weld penetration and fusion. - ✔✔ correct answer C) Bolt hole locations.



What type of symbol is used to express that a weld is to be completed in the field? (Multiple choice)

Question 13 options:A) A secondary welding symbol.B) A welding symbol.C) A basic welding
symbol.D) A supplementary symbol. - ✔✔ correct answer D) A supplementary symbol.



Where would the length of a test section be indicated? (Multiple choice)

Question 14 options:A) To the left of the symbol.B) To the right of the symbol.C) Above the symbol.D)
In the tail of the symbol. - ✔✔ correct answer B) To the right of the symbol.

, CWB Level 1 Weld Symbols
How is a request of test all around in the field indicated on a reference line? (Multiple choice)

Question 15 options:A) With a statement indicating test all around in the field is located in the tail of
a reference line.B) With a field weld symbol connected to the reference and arrow line intersect with
test all around indicated in the tail.C) With a test all around symbol centred wher the reference and
arrow line intersect with the test in field flag attached to the all around symbol.D) With a test all
around symbol centred where the reference and arrow line intersect with the test in field flag
attached to reference and arrow intersect. - ✔✔ correct answer C) With a test all around symbol
centred wher the reference and arrow line intersect with the test in field flag attached to the all
around symbol.



Where is a percentage of NDE requested? (Multiple choice)

Question 16 options:A) To the left of a NDE symbol.B) To the left of an NDE designation.C) To the
right of an NDE designation.D) Above the NDE designation. - ✔✔ correct answer C) To the right of an
NDE designation.



Multiple types of NDE can be identified on one symbol on any side or in the centre of a reference line
symbol. (True/False) - ✔✔ correct answer True



Which measurement is found on the reference line for a surfacing weld? (Multiple choice)

Question 18 options:A) The length.B) The width.C) The height.D) The area of surface covered. - ✔✔
correct answer C) The height.



Where is the size of the root opening of a weld joint shown? (Multiple choice)

Question 19 options:A) In the tail of the welding symbol.B) On the top surface of the weld symbol.C)
Inside the weld symbol.D) On the right side of the weld symbol. - ✔✔ correct answer C) Inside the
weld symbol.



What type of weld joint is used in joining two solid round bars, filled flush on both sides down their
length? (Multiple choice)

Question 20 options:A) A flare V-groove weld.B) A double bevel groove weld.C) A flare bevel groove
weldD) A double flare V-groove weld - ✔✔ correct answer D) A double flare V-groove weld



When is a back weld applied? (Multiple choice)

Question 21 options:A) After the groove weld in the symbol has been applied.B) Prior to the
completion of a groove weld.C) When there is limited access to the back side of the joint.D) When a
partial joint penetration groove weld is required. - ✔✔ correct answer A) After the groove weld in
the symbol has been applied