NCCER Core Curriculum, Module 5 Blueprints Questions and Answers correct

NCCER Core Curriculum, Module 5 Blueprints Questions and Answers correct civil plans Plans used for work that has to do with construction sheet tile What information in a drawing's title block identifies the project? structural plans The material to be used for the walls would be found in the... section cuts In the alphabet of lines, an area not included in the cutting line view is shown with... legend The information needed to identify lines and other symbols on a construction drawing only part of an object is represented to save space Break lines are used to show that.. Gridlines are used to... make it easy to refer to specific locations on plan number A dimension is a measurement written as a... is based on units of 10 One way that an engineer's scale differs from an architectural scale is that the engineer's scale... 5 feet If 1 inch equals 10 feet, the arrow on the engineer's scale in the figure above indicates a length of... Mechanical Which type of plan shows the layout of the HVAC system? lighting plans Electrical plans can include... revision blocks The title block generally contains... inside the title block The latest revision date on a set of construction drawings can be found... The Alphabet of Lines consists of.. the line types used on a construction drawing bays On a gridline system, a grid divides the area into small parts called... When the metric system is used, dimensions are written in... meters, centimeters, and milmetrrs If the scale on a site plan reads SCALE: 1" = 20'-0", then every... inch on the drawing represents 20 feet, 0 inches. 3.5 What is the length in meters at the point indicated by the arrow on the metric scale in review question figure 1 ? The unit of length used on the scale is the meter. An engineer's scale is up in multiples of.... 10 Site Plan shows the location of the building from an aerial view Revisions to the drawing are entered in the revision block and must include... date and initials of the person who made the revision symbols date and initials of the person who made the revision when a plan is marked in NTS, the dimensions as measured on the drawing cannot be used to build the project... true what is the length (in feet and inches) of the section of duct using the architectural's scales shown in section review question figure 1 ? 6 feet, 5 inches a __________ is a side view that shows height elevation drawing A_______________ usually has an arrowhead at both ends, with the measurement written near the middle of the line. dimension lines A_______________ is a qualified, licensed person who creates and Designs drawings for a construction project. architect Architectural Plans _____________, which shows the design of the project, include mini Parts, such as the floor plans, roof plans, elevation drawings, and section drawings. structural plans _____________support the architectural design of a building to show how the building is supported. A foundation plan would be part of this category. civil plans Also called the site plans or survey plans,__________ show the location of the building from an aerial view, as well as the natural Contours of the Earth. computer aiding drafting CAD almost all construction drawings today are made by..... Contour lines ____________are solid or dashed lines showing the elevation of the Earth on a civil drawing detailed drawings ____________are enlarged views of some special features of a building, such as floors and walls engineer A___________is a person who applies scientific principles in design and construction. electrical plans _____________________, or engineered drawings for electrical supply in distribution, including location of the electrical meter, switchgear, and convenience Outlets. beam a large, horizontal support made of concrete, steel, stone, or wood that may be shown in structural plans is a....... piping and instrumentation drawings (P&IDs) schematic drawings called__________ show all the equipment, pipelines, valves, instruments, and controls needed to operate a piping system. elevation an element of architectural drawings,__________ refers to the height above sea level or other Define surfaces. symbol architectural, civil and Structural Engineering, mechanical, and Plumbing_____________ may be used on a drawing to tell what material is required for the part of the project floor plans also called Plainview a___________ is an aerial view of the layout of each room. HVAC plans for gas, oil, or steam heat piping may be included in the_________ plans not to scale (NTS) when a plan is marked___________, it means that the drawing gives approximate positions in size only. hidden lines A____________is a dashed line on a plane showing an object obstruct from view by another object. Plumbing isometric drawing A_____________is a type of three-dimensional drawing that is included in a plumbing plan. metric scale the meter and millimeter are two common length of measurement used with the_____________ on architectural drawings. leader In drafting, an arrowhead is placed on a____________ to indicate a component. specifications ________________are written statements provided by the architectural and engineering firm to define the quality of work to be done in to describe the materials to be used. Legend The_____________Define the symbol used in architectural plans. mechanical plans ____________are engineered plans for Motors, pumps, piping systems, and piping equipment. section drawing A___________is a cross-section view that shows the inside of an object or building. architect's scale the Triangular and flat scales are the two most common types of... roof plans A______________shows the shape of the roof in the materials that will be used to finish it. Plumbing plans show the layout for the plumbing system that supplies hot in cold water, for the sewage Disposal system, and for the location of Plumbing fixtures. The_____________of a drawing tells the size of the object drawn compared with the actual size of the object represented. scale title block part of the construction drawing, the__________ gives information about the structure and is numbered for easy filing. blueprints ______________are the traditional name for construction drawing fire protection plans the drawing that makes up a building's piping, valves, and switches is a... Engineer's Scale A________ is used mainly for land measurements on site plans. architect a qualified, licensed person who creates and Designs drawings for a construction project. architect's scale a specialized ruler used in marking or measuring reduced scale drawings. The ruler is marked with a range of calibrated ratios for laying out distance, with scales indicating feet, inches, and fractions of inches. Used on drawings other than site plans. architectural plans drawings that show the design of the project. Also called architectural drawings. beam a large, horizontal structure member made of concrete, steel, stone, wood, or other Structural Materials to provide support above a large opening. blueprints the traditional name used to describe construction drawings. civil plans drawings that show the location of the building on the site from an aerial view, including Contours, trees, construction features, and dimensions. computer aided drafting CAD the making of a set of construction drawings with the aid of a computer. contour lines solid or dashed lines showing the elevation of the Earth on a civil drawing. detailed drawings enlarged views of part of a drawing used to show an area more clearly. dimension lines enlarged views of part of a drawing used to show an area more clearly. Electrical plans engineered drawings that show all electrical supplies and distribution elevation El height above sea level, or other Define surfaces, usually expressed in feet or meters. elevation drawing side view of a building or object, showing height and width. engineer a person who applies scientific principle in design and construction. engineer's scale a straight edge measuring distance divided uniformly into multiples of 10 divisions per inch so the drawings can be made with decimal values. Used mainly for land measurements on site plans. fire protection plan a drawing that shows the details of the building's sprinkler system. floor plan a drawing that provides an aerial view of the layout of each room Foundation plan A drawing that shows the layout and elevation of the building foundation hidden line a dashed line showing an object obstructed from view by another object. HVAC Heating, Ventilation and Air Conditioning