Alberta Welding First-Year Final AIT Exam Questions and Answers
A Material Safety Data every three years
Sheet must be reviewed
whenever new information
becomes available or at least
how often?
What is the total number of 1800
hours of work experience,
including technical training,
required per year in the
Welder
Apprenticeship Program?
Voltage-sensing wire feeders arc voltage.
set their speed according
to:
How much electrode stickout 10 mm to 19 mm (3/8" to 3/4")
is
recommended when using
gas shielded FCAW with 1.2
mm (0.045") wire?
One of the main functions of transfer current to the electrode.
the contact tube is to:
Flame propagation means False
the speed at which the fuel
gas will travel
What height limitation is in For free standing scaffolds, the scaffold must not be taller
place when using than three (3) times its smallest dimension in height
freestanding scaffolding?
The best reference point for datum line
dimensioning on pressure
vessels is the:
Which of the following is an UT
abbreviation of a Non
destructive test ?
In common fabricating 5
, practice, there are how
many basic joint types?
Single "V" butt joints are used 3/8" -1" (9.5 -25.4mm)
on material thicknesses of:
A small change in sling angle sling load.
can drastically affect the:
The power sources used for DC synergic, microprocessor-controlled.
pulsed spray transfer are:
Single "V" butt joints are used 3/8" -1" (9.5 -25.4mm)
on material thicknesses of:
If you must apply force to a suspended
load, always pull the load towards you.
When installing clips, the Live side of the wire
saddle side of the clip must
be placed on the:
When balancing a No. 2 1/4
welding tip and the
acetylene torch needle
valve is fully open, the
acetylene regulator should
be adjusted so that the
flame blows away from the
tip ____ inch. (Oxygen
needle valve is
closed)
Which ferrous-based metals stainless
cannot be cut satisfactorily
with an oxy-fuel cutting
torch?
What is the total number 240
of hours in the first
period Welder Training
Profile?
When starting a cut on plate, about 3 mm (1/8") above the surface.
the preheat cones should be
held:
What is the main purpose of transfers the welding current to the filler wire
A Material Safety Data every three years
Sheet must be reviewed
whenever new information
becomes available or at least
how often?
What is the total number of 1800
hours of work experience,
including technical training,
required per year in the
Welder
Apprenticeship Program?
Voltage-sensing wire feeders arc voltage.
set their speed according
to:
How much electrode stickout 10 mm to 19 mm (3/8" to 3/4")
is
recommended when using
gas shielded FCAW with 1.2
mm (0.045") wire?
One of the main functions of transfer current to the electrode.
the contact tube is to:
Flame propagation means False
the speed at which the fuel
gas will travel
What height limitation is in For free standing scaffolds, the scaffold must not be taller
place when using than three (3) times its smallest dimension in height
freestanding scaffolding?
The best reference point for datum line
dimensioning on pressure
vessels is the:
Which of the following is an UT
abbreviation of a Non
destructive test ?
In common fabricating 5
, practice, there are how
many basic joint types?
Single "V" butt joints are used 3/8" -1" (9.5 -25.4mm)
on material thicknesses of:
A small change in sling angle sling load.
can drastically affect the:
The power sources used for DC synergic, microprocessor-controlled.
pulsed spray transfer are:
Single "V" butt joints are used 3/8" -1" (9.5 -25.4mm)
on material thicknesses of:
If you must apply force to a suspended
load, always pull the load towards you.
When installing clips, the Live side of the wire
saddle side of the clip must
be placed on the:
When balancing a No. 2 1/4
welding tip and the
acetylene torch needle
valve is fully open, the
acetylene regulator should
be adjusted so that the
flame blows away from the
tip ____ inch. (Oxygen
needle valve is
closed)
Which ferrous-based metals stainless
cannot be cut satisfactorily
with an oxy-fuel cutting
torch?
What is the total number 240
of hours in the first
period Welder Training
Profile?
When starting a cut on plate, about 3 mm (1/8") above the surface.
the preheat cones should be
held:
What is the main purpose of transfers the welding current to the filler wire
