Exam (elaborations) NBCE:

6/17/25, 1:02 PM NBCE: Minor Surgery & Proctology Oregon Board Exam ACTUAL EXAM QUESTIONS WITH COMPLETE SOLUTION GUIDE (A+ …




NBCE: Minor Surgery & Proctology Oregon Board
Exam ACTUAL EXAM QUESTIONS WITH COMPLETE
SOLUTION GUIDE (A+ GRADED 100% VERIFIED)
LATEST VERSION
2025!!


A document that asserts D compliance
that a product conforms
to
specification is known as a
certificate of
(A) qualification

(B) validation

(C) calibration

compliance
(D)

Confidence limits are C interval within which a population parameter lies
generated in order to define
the
(A) limits of random
variation around a
control value
(B) limits that contain
all future
observations
(C) interval within which a
population parameter
lies
(D) amount of variation
that the process exhibits
The purpose of a calibration A detect deterioration of accuracy
schedule is to
(A) detect deterioration of
accuracy
(B) meet ISO audit requirements

(C) test inspector performance


-… 1/63

,6/17/25, 1:02 PM NBCE: Minor Surgery & Proctology Oregon Board Exam ACTUAL EXAM QUESTIONS WITH COMPLETE SOLUTION GUIDE (A+ …


(D) increase product
acceptance



What is the percent yield D 83.99%
for a normally distributed
process in which the item
length specification is
5.750 ± 0.004, X is 5.752, and
the standard deviation is
0.002 ?
(A) 15.73%

(B) 19.15%

(C) 47.72%

83.99%
(D)

In preparation for C record everything people suggest
construction of a cause and
effect
diagram, it is important to
(A) plot separate charts for
each source
(B) focus only on what

makes things go wrong
(C) record everything people
suggest
(D) validate possible root
causes
A quality technician uses a c C 2.48 24.52
chart to
monitor the number of
defects in a square foot of
material. After the initial
startup period, the mean
number of defects is
calculated at 13.5. What
should the control limits be
for the c chart?
LCL UCL
(A) 0.00 54.00




-… 2/63

,6/17/25, 1:02 PM NBCE: Minor Surgery & Proctology Oregon Board Exam ACTUAL EXAM QUESTIONS WITH COMPLETE SOLUTION GUIDE (A+ …


(B) 0.00 27.00
(C) 2.48 24.52

(D) 9.83 17.17




- C positively skewed
--
--
--
--
-
The shape of the distribution
above is best described as
(A) normal

(B) multi-modal

(C) positively skewed

negatively skew
(D)

A material review board A Analyzing and dispositioning of
(MRB) usually has the nonconforming material
responsibility for which of the
following?
(A) Analyzing and

dispositioning of
nonconforming
material
(B) Defining the statistical

specifications of
nonconforming material
(C) Assuring the availability
of materials to meet
production schedules
(D) Controlling the cost of
materials
The most common form of C blueprint
specification in
manufacturing
facilities is the
(A) control plan

-… 3/63

, 6/17/25, 1:02 PM NBCE: Minor Surgery & Proctology Oregon Board Exam ACTUAL EXAM QUESTIONS WITH COMPLETE SOLUTION GUIDE (A+ …


(B) operator instruction sheet
(C) blueprint

(D) in-process check sheet




Statistical quality control C close to the point of production of the part
generally requires inspection
to be conducted
(A) at the warehouse to
maintain quality of parts in
storage
(B) immediately after the
production run has been
completed
(C) close to the point of

production of the part
(D) when the product is
received by the customer
A process is running 1.5% A 0.0221
defective. The sampling
plan
used for this process is n= 40;
accept/reject
= 2/3. What is
the probability of rejecting a
lot from this process?
(A) 0.0221

(B) 0.0988

(C) 0.1209

(D) 0.3328

Inspection accuracy increases B repeated inspections
with
(A) reductions in defect rates

(B) repeated inspections

(C) additional product
complexity
(D) order of sample selection




-… 4/63