ASE MLR Certification Test Exam Questions
And Answers
Both A and B - - -
correct answer ✅Technician observes that the brake fluid level is
at the "Min" mark in the master cylinder reservoir. Tech A says that
worn front pads could be the cause. Tech B says that a leak in the
brake hydraulic system could be the cause. Who is right?
A only - - -
correct answer ✅The tires of a vehicle are being rotated and
balanced. Tech A says that the wheel weight retaining clips must be
matched to the rim profile. Tech B says that directional tires are
rotated in a criss-cross pattern. Who is right?
Safely exit the building - - -
correct answer ✅When a shop fire cannot be immediately
contained, the best thing to do is warn others in the area, and:
300 amps for 15 seconds - - -
correct answer ✅A fully charged battery rated at 600 CCA, the
ambient temperature is 70 degrees which of these current and time
periods should be used?
B only - - -
correct answer ✅A vehicle's halogen headlamp bulbs are being
,ASE MLR Certification Test Exam Questions
And Answers
replaced. Technician A says the glass part of the bulb can only be
handled with bare hands. Technician B says the headlamp may
need to be removed. Who is right?
0.728 - - -
correct answer ✅On a Metric Micrometer upper sleeve reading
5.0mm with lower sleeve reading 0.50mm and a thimble reading of
0.01mm what is the overall reading?
A only - - -
correct answer ✅The fuel filter on a fuel-injected vehicle is being
replaced. Tech A says the fuel pressure should be relieved before
removing the filter. Tech B says that the arrow on the fuel filter
should point towards the fuel tank. Who is right?
The brake pedal feels low and spongy - - -
correct answer ✅Which of these is an indication of air in the brake
hydraulic system?
Anaerobic - - -
correct answer ✅Which of these cures in the absence of air?
, ASE MLR Certification Test Exam Questions
And Answers
Fluid contaminated brake linings - - -
correct answer ✅A grabbing brake condition can be caused by any
of these EXCEPT:
Visually verify that the oil filter gasket is properly installed - - -
correct answer ✅When performing an oil filter change on a
vehicle with a spin on oil filter, the technician must:
Voltage regulation - - -
correct answer ✅A vehicle's battery prematurely fails. A charging
system output test shows the generator (alternator) is producing a
constant 16.0 volts. This could indicate a failed:
Seal should be lubricated with transmission fluid - - -
correct answer ✅A transmission equipped with a filter is being
serviced. When installing the new filter, the:
Both A and B - - -
correct answer ✅While inspecting the rear axle wheel studs on a
rear-wheel drive vehicle, the technician observed that one stud is
damaged. Technician A says that all the wheel studs on the hub
assembly should be replaced. Technician B says that the thread
And Answers
Both A and B - - -
correct answer ✅Technician observes that the brake fluid level is
at the "Min" mark in the master cylinder reservoir. Tech A says that
worn front pads could be the cause. Tech B says that a leak in the
brake hydraulic system could be the cause. Who is right?
A only - - -
correct answer ✅The tires of a vehicle are being rotated and
balanced. Tech A says that the wheel weight retaining clips must be
matched to the rim profile. Tech B says that directional tires are
rotated in a criss-cross pattern. Who is right?
Safely exit the building - - -
correct answer ✅When a shop fire cannot be immediately
contained, the best thing to do is warn others in the area, and:
300 amps for 15 seconds - - -
correct answer ✅A fully charged battery rated at 600 CCA, the
ambient temperature is 70 degrees which of these current and time
periods should be used?
B only - - -
correct answer ✅A vehicle's halogen headlamp bulbs are being
,ASE MLR Certification Test Exam Questions
And Answers
replaced. Technician A says the glass part of the bulb can only be
handled with bare hands. Technician B says the headlamp may
need to be removed. Who is right?
0.728 - - -
correct answer ✅On a Metric Micrometer upper sleeve reading
5.0mm with lower sleeve reading 0.50mm and a thimble reading of
0.01mm what is the overall reading?
A only - - -
correct answer ✅The fuel filter on a fuel-injected vehicle is being
replaced. Tech A says the fuel pressure should be relieved before
removing the filter. Tech B says that the arrow on the fuel filter
should point towards the fuel tank. Who is right?
The brake pedal feels low and spongy - - -
correct answer ✅Which of these is an indication of air in the brake
hydraulic system?
Anaerobic - - -
correct answer ✅Which of these cures in the absence of air?
, ASE MLR Certification Test Exam Questions
And Answers
Fluid contaminated brake linings - - -
correct answer ✅A grabbing brake condition can be caused by any
of these EXCEPT:
Visually verify that the oil filter gasket is properly installed - - -
correct answer ✅When performing an oil filter change on a
vehicle with a spin on oil filter, the technician must:
Voltage regulation - - -
correct answer ✅A vehicle's battery prematurely fails. A charging
system output test shows the generator (alternator) is producing a
constant 16.0 volts. This could indicate a failed:
Seal should be lubricated with transmission fluid - - -
correct answer ✅A transmission equipped with a filter is being
serviced. When installing the new filter, the:
Both A and B - - -
correct answer ✅While inspecting the rear axle wheel studs on a
rear-wheel drive vehicle, the technician observed that one stud is
damaged. Technician A says that all the wheel studs on the hub
assembly should be replaced. Technician B says that the thread
