##SOS Mechanic Certification- Brakes
real exam*spleadid*
Most 1995 & newer vehicles use which of the following types of wheels bearings on
non-drive wheel? - ANSWERSSealed non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump the brake pedal
at least 4 times, hold the brake pedal depressed, and start the engine. the brake pedal
should: - ANSWERSdrop slightly and remain firm
You are installing a set of brake shoe linings that are not the same length. Traditionally,
the primary shoe lining is: - ANSWERSSmaller and goes towards the front of the car.
A cracked or torn vacuum diaphragm in a brake power booster would most likely
cause: - ANSWERSa hard pedal feel requiring very high pedal effort to stop
A mechanic finds gear lube inside both rear brake drums on a rear wheel drive vehicle.
What is the most likely cause of this problem? - ANSWERSA plugged axle
Which of the following incorrect service procedures will cause brake lock-up? -
ANSWERSmaster cylinder push rod adjusted too long
Which of the following describes the proper way to depressurized an ABS system? -
ANSWERSPump the brake pedal at least 25 times (or more, depending on the
manufacturer's recommendation) with the ignition off.
The rear brakes are dragging after having new linings installed and the drums
machined. the most likely cause is the: - ANSWERStechnician use the parking brake to
adjust shoes and the cable is stuck
When turning brake drums: - ANSWERSuse a dampening strap to reduce chatter
Which of the following is NOT a necessary drum brake measurement? -
ANSWERSrun-out
On a 3-channel system, which wheels are on the same circuit? - ANSWERSboth rear
wheels
One way to test an ABS wheel speed signal is to use _____ on your digital multimeter.
- ANSWERSAC volts
The key input for the ABS control module comes from the: - ANSWERSwheel speed
sensors
, ABS speed sensor and sensor rings: - ANSWERSshould not be hammered or tapped
on and should always be replaced as a matched set
Flexible brake hoses should be replaced: - ANSWERSwhen dampness is evident on
the hose
Which of the following should be used to check for rotor thickness variation: -
ANSWERSMicrometer
After rebuilding a master cylinder, the rod between the master cylinder and booster
should be: - ANSWERSadjusted properly
Upon inspecting brake fluid condition, the technician observes the diaphragm in the
master cylinder cup is swollen. Which of the following is the most likely cause? -
ANSWERSsilicone fluid added to the system
When inspecting brake fluid levels, a technician observes low fluid levels. which of the
following should be done first? - ANSWERSInspect disc brake pads for excessive wear
Which of the following is true about most properly functioning anti-lock brake systems?
- ANSWERSThe brakes may lock up at speeds less than 10 miles per hour
Which of the following is true about bleeding brake lines on most ABS equipped
vehicles? - ANSWERSMost ABS brake lines can be bled like a conventional (non-ABS)
system. However, caution must be taken because of the extreme pressure.
Most anti-lock brake systems require the removal of the pressure modulator fuse when:
- ANSWERSa "spaced-saver" spare tire is being used and mismatched tires are being
installed
What does a load sensing proportioning valve do? - ANSWERSIt increases the
hydraulic pressure during braking at the rear wheel cylinders when the vehicle is loaded
The brakes of a car squeal each time they are applied, which of the following is the
LEAST likely source of the noise? - ANSWERSGlazed brake pads
Which of the following is a true statement about proportioning valves? -
ANSWERSThey provide better braking balance during hard stops
A properly functioning load sensing proportioning valve will: - ANSWERScause an
increase in the hydraulic pressure during braking at the rear wheel cylinders when the
vehicle is loaded.
Why don't disc brake system usually need adjustment? - ANSWERSA certain amount
of pressure is maintained by the metering valve
real exam*spleadid*
Most 1995 & newer vehicles use which of the following types of wheels bearings on
non-drive wheel? - ANSWERSSealed non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump the brake pedal
at least 4 times, hold the brake pedal depressed, and start the engine. the brake pedal
should: - ANSWERSdrop slightly and remain firm
You are installing a set of brake shoe linings that are not the same length. Traditionally,
the primary shoe lining is: - ANSWERSSmaller and goes towards the front of the car.
A cracked or torn vacuum diaphragm in a brake power booster would most likely
cause: - ANSWERSa hard pedal feel requiring very high pedal effort to stop
A mechanic finds gear lube inside both rear brake drums on a rear wheel drive vehicle.
What is the most likely cause of this problem? - ANSWERSA plugged axle
Which of the following incorrect service procedures will cause brake lock-up? -
ANSWERSmaster cylinder push rod adjusted too long
Which of the following describes the proper way to depressurized an ABS system? -
ANSWERSPump the brake pedal at least 25 times (or more, depending on the
manufacturer's recommendation) with the ignition off.
The rear brakes are dragging after having new linings installed and the drums
machined. the most likely cause is the: - ANSWERStechnician use the parking brake to
adjust shoes and the cable is stuck
When turning brake drums: - ANSWERSuse a dampening strap to reduce chatter
Which of the following is NOT a necessary drum brake measurement? -
ANSWERSrun-out
On a 3-channel system, which wheels are on the same circuit? - ANSWERSboth rear
wheels
One way to test an ABS wheel speed signal is to use _____ on your digital multimeter.
- ANSWERSAC volts
The key input for the ABS control module comes from the: - ANSWERSwheel speed
sensors
, ABS speed sensor and sensor rings: - ANSWERSshould not be hammered or tapped
on and should always be replaced as a matched set
Flexible brake hoses should be replaced: - ANSWERSwhen dampness is evident on
the hose
Which of the following should be used to check for rotor thickness variation: -
ANSWERSMicrometer
After rebuilding a master cylinder, the rod between the master cylinder and booster
should be: - ANSWERSadjusted properly
Upon inspecting brake fluid condition, the technician observes the diaphragm in the
master cylinder cup is swollen. Which of the following is the most likely cause? -
ANSWERSsilicone fluid added to the system
When inspecting brake fluid levels, a technician observes low fluid levels. which of the
following should be done first? - ANSWERSInspect disc brake pads for excessive wear
Which of the following is true about most properly functioning anti-lock brake systems?
- ANSWERSThe brakes may lock up at speeds less than 10 miles per hour
Which of the following is true about bleeding brake lines on most ABS equipped
vehicles? - ANSWERSMost ABS brake lines can be bled like a conventional (non-ABS)
system. However, caution must be taken because of the extreme pressure.
Most anti-lock brake systems require the removal of the pressure modulator fuse when:
- ANSWERSa "spaced-saver" spare tire is being used and mismatched tires are being
installed
What does a load sensing proportioning valve do? - ANSWERSIt increases the
hydraulic pressure during braking at the rear wheel cylinders when the vehicle is loaded
The brakes of a car squeal each time they are applied, which of the following is the
LEAST likely source of the noise? - ANSWERSGlazed brake pads
Which of the following is a true statement about proportioning valves? -
ANSWERSThey provide better braking balance during hard stops
A properly functioning load sensing proportioning valve will: - ANSWERScause an
increase in the hydraulic pressure during braking at the rear wheel cylinders when the
vehicle is loaded.
Why don't disc brake system usually need adjustment? - ANSWERSA certain amount
of pressure is maintained by the metering valve
