IRONWORKER NCCER QUESTIONS AND ANSWERS
100% GUARANTEED PASS! 2025 EDITION| GRADED
A+
ASSUMING A GRIP DISTANCE OF 1", WHAT IS THE MINIMUN LENGTH OF THE BOLT REQUIRED
FOR A 3/4" DIAMETER BOLT? - ANSWER 2 1/4"
THE LOCATION OF BRIDGING DEPENDS ON THE LENGTH OF THE: - ANSWER SPAN
BEFORE BUNDLES OF DECK CAN BE LANDED ON A BAR JOIST, WHAT ACTION MUST BE
COMPLETED? - ANSWER JOIST MUST HAVE BRIDGING INSTALLED
WHEN MATERIALS ARE BEING HOISTED TO AN UPPER LEVEL, A TAG LINE IS USED TO: - ANSWER
HELP CONTROL THE LOAD
ITEMS SUCH AS FIELD WELDING INSTRUCTIONS, HANGERS, AND CONNECTION DETAILS ARE
GENERALLY FOUND ON: - ANSWER THE DETAIL DRAWINGS
THE ABILITY OF A STRUCTURAL STEEL COMPONENT TO RESIST PULLING FORCES IS KNOWN AS: -
ANSWER TENSILE STRENGHT
WHAT TYPE OF DECKING HAS IMPRESSIONS FORMED ON ITS RIB? - ANSWER COMPOSITE DECK
THE GROUND FLOOR ELEVATION IS SHOWN AS +100.25. THE ROOF TOP ELEVATION IS SHOWN
AS +130.50. WHAT IS THE DIFFERENCE IN ELEVATION? - ANSWER 30'3
IN WHAT DRAWING WOULD ONE FIND THE CORRECT BOLT SIZE FOR A BEAM BEING BOLTED? -
ANSWER DETAIL DRAWING
, WHAT SHOULD ALWAYS BE USED TO IGNITE A CUTTING TORCH? - ANSWER STRIKER
EQUILIZING THE WEIGHT OF THE LOAD AT VARIOUS LIFTING POINTS IS CALLED: - ANSWER
CONFIGURATION
A COMBINATION SQUARE WITHOUT A PROTRACTOR HEAD IS USED TO LAYOUT: - ANSWER 45
DEGREE LINES
PRIOR TO INSPECTION IT IS GOOD PRACTICE TO TEST ALL STUDS WITH WHAT METHOD? -
ANSWER PING TEST
WHERE IS THE FULCRUM OR PIVOT POINT ON A FORKLIFT? - ANSWER THE FRONT AXLE
A DOCUMENT THAT OUTLINES WEIGHTS,CRANE CONFIGURATION AND RIGGING
REQUIREMENTS FOR A LIFT IS CALLED AN: - ANSWER LIFT PLAN
WHERE CAN THE BOLTING METHODS REGARDING STRUCTURAL STEEL USUALLY BE FOUND ? -
ANSWER IN THE GENERAL NOTES OF THE STRUCTURAL DRAWINGS
WHEN ESTABLISHING ELEVATIONS OF STRUCTURAL STEEL MEMBERS, THE REFERENCE POINT
USED TO DETERMINE ALL OTHER ELEVATIONS IS CALLED? - ANSWER THE BENCHMARK
WHAT IS THE SURFACE AREA OF A RECTANGLE WITH THE DIMENSIONS OF 30'6" TALL AND 6
FEET WIDE? - ANSWER 183FT
MEASUREMENTS FROM THE CENTER OF THE CRANES AXIS OF ROTATION TO THE CENTER OF
THE LOAD LINE WITH THE LOAD APPLIED IS: - ANSWER LOAD RADIUS
100% GUARANTEED PASS! 2025 EDITION| GRADED
A+
ASSUMING A GRIP DISTANCE OF 1", WHAT IS THE MINIMUN LENGTH OF THE BOLT REQUIRED
FOR A 3/4" DIAMETER BOLT? - ANSWER 2 1/4"
THE LOCATION OF BRIDGING DEPENDS ON THE LENGTH OF THE: - ANSWER SPAN
BEFORE BUNDLES OF DECK CAN BE LANDED ON A BAR JOIST, WHAT ACTION MUST BE
COMPLETED? - ANSWER JOIST MUST HAVE BRIDGING INSTALLED
WHEN MATERIALS ARE BEING HOISTED TO AN UPPER LEVEL, A TAG LINE IS USED TO: - ANSWER
HELP CONTROL THE LOAD
ITEMS SUCH AS FIELD WELDING INSTRUCTIONS, HANGERS, AND CONNECTION DETAILS ARE
GENERALLY FOUND ON: - ANSWER THE DETAIL DRAWINGS
THE ABILITY OF A STRUCTURAL STEEL COMPONENT TO RESIST PULLING FORCES IS KNOWN AS: -
ANSWER TENSILE STRENGHT
WHAT TYPE OF DECKING HAS IMPRESSIONS FORMED ON ITS RIB? - ANSWER COMPOSITE DECK
THE GROUND FLOOR ELEVATION IS SHOWN AS +100.25. THE ROOF TOP ELEVATION IS SHOWN
AS +130.50. WHAT IS THE DIFFERENCE IN ELEVATION? - ANSWER 30'3
IN WHAT DRAWING WOULD ONE FIND THE CORRECT BOLT SIZE FOR A BEAM BEING BOLTED? -
ANSWER DETAIL DRAWING
, WHAT SHOULD ALWAYS BE USED TO IGNITE A CUTTING TORCH? - ANSWER STRIKER
EQUILIZING THE WEIGHT OF THE LOAD AT VARIOUS LIFTING POINTS IS CALLED: - ANSWER
CONFIGURATION
A COMBINATION SQUARE WITHOUT A PROTRACTOR HEAD IS USED TO LAYOUT: - ANSWER 45
DEGREE LINES
PRIOR TO INSPECTION IT IS GOOD PRACTICE TO TEST ALL STUDS WITH WHAT METHOD? -
ANSWER PING TEST
WHERE IS THE FULCRUM OR PIVOT POINT ON A FORKLIFT? - ANSWER THE FRONT AXLE
A DOCUMENT THAT OUTLINES WEIGHTS,CRANE CONFIGURATION AND RIGGING
REQUIREMENTS FOR A LIFT IS CALLED AN: - ANSWER LIFT PLAN
WHERE CAN THE BOLTING METHODS REGARDING STRUCTURAL STEEL USUALLY BE FOUND ? -
ANSWER IN THE GENERAL NOTES OF THE STRUCTURAL DRAWINGS
WHEN ESTABLISHING ELEVATIONS OF STRUCTURAL STEEL MEMBERS, THE REFERENCE POINT
USED TO DETERMINE ALL OTHER ELEVATIONS IS CALLED? - ANSWER THE BENCHMARK
WHAT IS THE SURFACE AREA OF A RECTANGLE WITH THE DIMENSIONS OF 30'6" TALL AND 6
FEET WIDE? - ANSWER 183FT
MEASUREMENTS FROM THE CENTER OF THE CRANES AXIS OF ROTATION TO THE CENTER OF
THE LOAD LINE WITH THE LOAD APPLIED IS: - ANSWER LOAD RADIUS
