ICC BOLTING EXAM WITH ACTUAL QUESTIONS AND
ANSWERS FROM A VERIFIED SOURCE GRADED A+.
According to the IBC, the "blank" is to hire the special inspector. -
ANSWERS-owner or owners agent. 2009 IBC Section 1704.1
When is the code official to be made aware of a discrepancy
found during a special inspection? - ANSWERS-If it is not corrected
by the contractor. 2009 IBC, Section 1704.1.2
According to the Model Program for Special Inspection, the
special inspector is to document work that is nonconforming: -
ANSWERS-In a written report - Section II B 4 - Model Programs
According to the Model Program for Special Inspection, the
special inspector is to prepare written report of inspection: -
ANSWERS-After each inspection visit - Section II B 5 - Model
Programs
According to the Model Program for Special Inspection, which of
the following items does not need to be included in each
inspection report? - ANSWERS-Description of discussions with the
contractor - Section B 5 - Model Programs
According to the Specification for Structural Joints using high
strength bolts, the nominal diameter of standard bolt holes shall
be how much larger than the nominal bolt diameter? - ANSWERS-
1/16 inch - Specification for Structural Joints Table 3.1
,Discrepancies in the work shall be brought to the immediate
attention of the "blank" for corrective action. - ANSWERS-the
contractor - 2009 IBC, Section 1704.1.2.
The special inspector shall furnish inspection reports to the
"blank" and to the "blank"? - ANSWERS-Building Official and
Registered Design professional
The special inspector shall provide continuos inspection of: -
ANSWERS-Single-pass fillet welds greater than 5/16 inch in size -
2099 IBC, Table 1704.3, Item 5.3
The special inspections required by this code are not required
where the work is done on the premise of a? - ANSWERS-Approved
fabricator - 2009 IBC, Section 1704.2.2
The special inspection of the steel fabrication process shall not be
required where the fabricator does not perform any? - ANSWERS-
heating operations - 2009 IBC, Section 1704.3, Exceptions # 1
According to the Specifications for Structural Steel Buildings,
ASTM Standard "blank" is to be used for the material test for steel
sheets. - ANSWERS-A568 - Section A31, Specifications for
Structural Steel Buildings
According to the Specifications for Structural Steel Buildings, the
"blank" conducts the material tests for identification of the
structural steel. - ANSWERS-Fabricator or Testing Laboratory -
Section A31, Specifications for Structural Steel Buildings.
According to the Specifications for Structural Steel Buildings,
which of the following steel members are allowed to be
unidentified steel? - ANSWERS-Unimportant members, where their
physical properties and weldability would not affect the structure
, strength - Section A31b, Specifications for Structural Steel
Buildings
According to the Code of Standard Practice for Steel Buildings
and Bridges, how is steel of special material to be identified? -
ANSWERS-It is marked by the supplier - Section 5.1.1, Code of
Standard Practice for Steel Buildings and Bridges
According to the Specification for Structural Steel Buildings, what
ASTM Standard would apply to a sample for structural steel pipe?
- ANSWERS-A53 - Section A31a - Specification for Structural Steel
Buildings
According to the Code of Standard Practice for Steel Buildings
and Bridges, the number of samples required to be tested for
structural steel is: - ANSWERS-The number specified by the ASTM
specification - Section 5.1.1 - Code of Standard Practice for Steel
Buildings and Bridges
According to the Specification for Structural Steel Buildings, which
ASTM standard would apply to a sample for structural steel
plates? - ANSWERS-A36, A283, and A242 - Section A31a -
Specification for Structural Steel Buildings
According to the Specification for Structural Steel Buildings,
"blank" tests are required for samples for built-up sections
consisting of plates over 2 inches in thickness. - ANSWERS-Charpy
V-notch testing - Section A31d, Specification for Structural Steel
Buildings
According to the Specification for Structural Steel Buildings,
ASTM standard "blank" would apply to a sample for structural
steel bars. - ANSWERS-A36, A529, and A572 - Specification for
Structural Steel Buildings
ANSWERS FROM A VERIFIED SOURCE GRADED A+.
According to the IBC, the "blank" is to hire the special inspector. -
ANSWERS-owner or owners agent. 2009 IBC Section 1704.1
When is the code official to be made aware of a discrepancy
found during a special inspection? - ANSWERS-If it is not corrected
by the contractor. 2009 IBC, Section 1704.1.2
According to the Model Program for Special Inspection, the
special inspector is to document work that is nonconforming: -
ANSWERS-In a written report - Section II B 4 - Model Programs
According to the Model Program for Special Inspection, the
special inspector is to prepare written report of inspection: -
ANSWERS-After each inspection visit - Section II B 5 - Model
Programs
According to the Model Program for Special Inspection, which of
the following items does not need to be included in each
inspection report? - ANSWERS-Description of discussions with the
contractor - Section B 5 - Model Programs
According to the Specification for Structural Joints using high
strength bolts, the nominal diameter of standard bolt holes shall
be how much larger than the nominal bolt diameter? - ANSWERS-
1/16 inch - Specification for Structural Joints Table 3.1
,Discrepancies in the work shall be brought to the immediate
attention of the "blank" for corrective action. - ANSWERS-the
contractor - 2009 IBC, Section 1704.1.2.
The special inspector shall furnish inspection reports to the
"blank" and to the "blank"? - ANSWERS-Building Official and
Registered Design professional
The special inspector shall provide continuos inspection of: -
ANSWERS-Single-pass fillet welds greater than 5/16 inch in size -
2099 IBC, Table 1704.3, Item 5.3
The special inspections required by this code are not required
where the work is done on the premise of a? - ANSWERS-Approved
fabricator - 2009 IBC, Section 1704.2.2
The special inspection of the steel fabrication process shall not be
required where the fabricator does not perform any? - ANSWERS-
heating operations - 2009 IBC, Section 1704.3, Exceptions # 1
According to the Specifications for Structural Steel Buildings,
ASTM Standard "blank" is to be used for the material test for steel
sheets. - ANSWERS-A568 - Section A31, Specifications for
Structural Steel Buildings
According to the Specifications for Structural Steel Buildings, the
"blank" conducts the material tests for identification of the
structural steel. - ANSWERS-Fabricator or Testing Laboratory -
Section A31, Specifications for Structural Steel Buildings.
According to the Specifications for Structural Steel Buildings,
which of the following steel members are allowed to be
unidentified steel? - ANSWERS-Unimportant members, where their
physical properties and weldability would not affect the structure
, strength - Section A31b, Specifications for Structural Steel
Buildings
According to the Code of Standard Practice for Steel Buildings
and Bridges, how is steel of special material to be identified? -
ANSWERS-It is marked by the supplier - Section 5.1.1, Code of
Standard Practice for Steel Buildings and Bridges
According to the Specification for Structural Steel Buildings, what
ASTM Standard would apply to a sample for structural steel pipe?
- ANSWERS-A53 - Section A31a - Specification for Structural Steel
Buildings
According to the Code of Standard Practice for Steel Buildings
and Bridges, the number of samples required to be tested for
structural steel is: - ANSWERS-The number specified by the ASTM
specification - Section 5.1.1 - Code of Standard Practice for Steel
Buildings and Bridges
According to the Specification for Structural Steel Buildings, which
ASTM standard would apply to a sample for structural steel
plates? - ANSWERS-A36, A283, and A242 - Section A31a -
Specification for Structural Steel Buildings
According to the Specification for Structural Steel Buildings,
"blank" tests are required for samples for built-up sections
consisting of plates over 2 inches in thickness. - ANSWERS-Charpy
V-notch testing - Section A31d, Specification for Structural Steel
Buildings
According to the Specification for Structural Steel Buildings,
ASTM standard "blank" would apply to a sample for structural
steel bars. - ANSWERS-A36, A529, and A572 - Specification for
Structural Steel Buildings
