1c|cPc ac gc e
ARF 2006 FINAL REVIEW EXAM|| LATELY UPDATE
c c c c c c
D QUESTIONS AND 100% CORRECT ANSWERS ALR
c c c c c c
EADY GRADED A|| LATEST AND COMPLETE UPDAT c c c c c c
E 2025 WITH VERIFIED SOLUTIONS|| ASSURED PAS
c c c c c c
S!!!
Fairleads should never deflect the alignment of a cable more than? 3
c c c c c c c c c c c c
degrees
When installing a castle nut, start alignment with the cotter pin hole at the Minimum r
c c c c c c c c c c c c c c c
ecommended torque plus friction drag torque c c c c c
If the control stick of an aircraft with properly rigged flight controls is moved rearwar
c c c c c c c c c c c c c c
d and to the left, the right aileron will move?
c c c c c c c c c
Down and the elevator will move up
c c c c c c
The chord of a wing is measured from leadin
c c c c c c c c
g edge to trailing edge
c c c c
The acute angle formed by the chord line of a wing and the relative wind is known as t
c c c c c c c c c c c c c c c c c c
he?
Angle of Attack c c
,2c|cPc ac gc e
A tension regulator in the flight control cable system of a large all-
c c c c c c c c c c c c
metal aircraft is used primarily to
c c c c c
Retain a set tension c c c
Where is fuselage station No. 137 located?
c c c c c c
137 inches after of the zero or fixed reference line
c c c c c c c c c
Stability about the axis which runs parallel to the line of flight is referred to as? Lateral S
c c c c c c c c c c c c c c c c c
tability
Placing a piece of cloth around a stainless steel control cable and running it back and f
c c c c c c c c c c c c c c c c
orth over the length of the cable is generally a satisfactory method of inspecting for
c c c c c c c c c c c c c c
Broken strands c
If all instructions issued by the swaging tool manufacturer are followed when swagin
c c c c c c c c c c c c
g a cable terminal, the resultant swaged terminal strength should be
c c c c c c c c c c
Full rated strength of the cable
c c c c c
Where does the breakage of control cable wires occur most frequently? Breakage
c c c c c c c c c c c
usually occurs where cables pass over pulleys and through fairleads.
c c c c c c c c c c
, 3c|cPc ac gc e
What minimum distance must all pulleys and fairleads be from a turnbuckle? At l
c c c c c c c c c c c c c
east 2" c
Other than the manufacturer maintenance manual what other document could be used
c c c c c c c c c c c
cto determine the primary flight control surface deflection for an imported aircraft tha
c c c c c c c c c c c c
t is reassembled after shipment?
c c c c
Aircraft type certificate data sheetc c c c
The universal propeller protractor can be used to measure D
c c c c c c c c c
egrees of flap travel c c c
Are negative safeties allowed? No
c c c c
Cable misalignment will be evident by?
c c c c c
Excessive wear on one of the sides of the control cable pulley
c c c c c c c c c c c
What would be the indication of pulley misalignment Wear
c c c c c c c c c
on both sides of pulley
c c c c
ARF 2006 FINAL REVIEW EXAM|| LATELY UPDATE
c c c c c c
D QUESTIONS AND 100% CORRECT ANSWERS ALR
c c c c c c
EADY GRADED A|| LATEST AND COMPLETE UPDAT c c c c c c
E 2025 WITH VERIFIED SOLUTIONS|| ASSURED PAS
c c c c c c
S!!!
Fairleads should never deflect the alignment of a cable more than? 3
c c c c c c c c c c c c
degrees
When installing a castle nut, start alignment with the cotter pin hole at the Minimum r
c c c c c c c c c c c c c c c
ecommended torque plus friction drag torque c c c c c
If the control stick of an aircraft with properly rigged flight controls is moved rearwar
c c c c c c c c c c c c c c
d and to the left, the right aileron will move?
c c c c c c c c c
Down and the elevator will move up
c c c c c c
The chord of a wing is measured from leadin
c c c c c c c c
g edge to trailing edge
c c c c
The acute angle formed by the chord line of a wing and the relative wind is known as t
c c c c c c c c c c c c c c c c c c
he?
Angle of Attack c c
,2c|cPc ac gc e
A tension regulator in the flight control cable system of a large all-
c c c c c c c c c c c c
metal aircraft is used primarily to
c c c c c
Retain a set tension c c c
Where is fuselage station No. 137 located?
c c c c c c
137 inches after of the zero or fixed reference line
c c c c c c c c c
Stability about the axis which runs parallel to the line of flight is referred to as? Lateral S
c c c c c c c c c c c c c c c c c
tability
Placing a piece of cloth around a stainless steel control cable and running it back and f
c c c c c c c c c c c c c c c c
orth over the length of the cable is generally a satisfactory method of inspecting for
c c c c c c c c c c c c c c
Broken strands c
If all instructions issued by the swaging tool manufacturer are followed when swagin
c c c c c c c c c c c c
g a cable terminal, the resultant swaged terminal strength should be
c c c c c c c c c c
Full rated strength of the cable
c c c c c
Where does the breakage of control cable wires occur most frequently? Breakage
c c c c c c c c c c c
usually occurs where cables pass over pulleys and through fairleads.
c c c c c c c c c c
, 3c|cPc ac gc e
What minimum distance must all pulleys and fairleads be from a turnbuckle? At l
c c c c c c c c c c c c c
east 2" c
Other than the manufacturer maintenance manual what other document could be used
c c c c c c c c c c c
cto determine the primary flight control surface deflection for an imported aircraft tha
c c c c c c c c c c c c
t is reassembled after shipment?
c c c c
Aircraft type certificate data sheetc c c c
The universal propeller protractor can be used to measure D
c c c c c c c c c
egrees of flap travel c c c
Are negative safeties allowed? No
c c c c
Cable misalignment will be evident by?
c c c c c
Excessive wear on one of the sides of the control cable pulley
c c c c c c c c c c c
What would be the indication of pulley misalignment Wear
c c c c c c c c c
on both sides of pulley
c c c c
