RVTI - PDI QUESTIONS WITH VERIFIED
ANSWERS
Propane - Preparing to Run Propane Test - ANSWERStep 1: Verify Propane in
container - briefly open outage valve and listen for release of vapor
Propane - Setting the Pressure - ANSWERStep 1: Connect a calibrated manometer-
connect manometer to barbed fitting
Propane - Lockup Pressure Test - ANSWERStep 1: Prepare for and perform lock up
test - close the orifice valve on test apparatus while watching manometer measurement.
Propane - Timed Pressure Drop Test - ANSWERStep 1: Prepare for times pressure
drop test - close the service valve fully
Propane - Bubble Solution Test - ANSWERStep 1: Perform bubble test - open service
valve and bubble test all fittings that had been removed and reinstalled during test
procedures using detection solution
Water - Fresh Water System - ANSWERStep 1: Pump strainer - inspect water pump
strainer, clean if 'tank trash' is visible
Water - Leak Test - ANSWERStep 1: Leak Test - turn off the city water
Water - Fixture Flow Test - ANSWERStep 1: Level RV - Orient RV into level position
Electric - Battery Inspection - ANSWERStep 1: Battery Box - Confirm battery is vapor
tight from the inside of the RV and properly vented
Electric - Converter Output Circuits - ANSWERStep 1: Fuses and Circuit Breaker -
visually inspect fuses or circuit breakers
Electric - Power Converters - ANSWERStep 1: Documentation and Prepare - Assemble
documentation and plug coach into AC power source
Electric - Parallel Battery Bank - ANSWERStep 1: Configure batteries on test bench -
batteries properly oriented; positive and negative
Electric - Safety Ground Conductor Continuity - ANSWERStep 1: Access Shore Cord
Electric - Hot Skin Test - ANSWERStep 1: Preparation for the Test - Assembled
documentation for performing HST
Step 2: Voltage at Source and Polarity - Measured voltage at source before plugging in
ANSWERS
Propane - Preparing to Run Propane Test - ANSWERStep 1: Verify Propane in
container - briefly open outage valve and listen for release of vapor
Propane - Setting the Pressure - ANSWERStep 1: Connect a calibrated manometer-
connect manometer to barbed fitting
Propane - Lockup Pressure Test - ANSWERStep 1: Prepare for and perform lock up
test - close the orifice valve on test apparatus while watching manometer measurement.
Propane - Timed Pressure Drop Test - ANSWERStep 1: Prepare for times pressure
drop test - close the service valve fully
Propane - Bubble Solution Test - ANSWERStep 1: Perform bubble test - open service
valve and bubble test all fittings that had been removed and reinstalled during test
procedures using detection solution
Water - Fresh Water System - ANSWERStep 1: Pump strainer - inspect water pump
strainer, clean if 'tank trash' is visible
Water - Leak Test - ANSWERStep 1: Leak Test - turn off the city water
Water - Fixture Flow Test - ANSWERStep 1: Level RV - Orient RV into level position
Electric - Battery Inspection - ANSWERStep 1: Battery Box - Confirm battery is vapor
tight from the inside of the RV and properly vented
Electric - Converter Output Circuits - ANSWERStep 1: Fuses and Circuit Breaker -
visually inspect fuses or circuit breakers
Electric - Power Converters - ANSWERStep 1: Documentation and Prepare - Assemble
documentation and plug coach into AC power source
Electric - Parallel Battery Bank - ANSWERStep 1: Configure batteries on test bench -
batteries properly oriented; positive and negative
Electric - Safety Ground Conductor Continuity - ANSWERStep 1: Access Shore Cord
Electric - Hot Skin Test - ANSWERStep 1: Preparation for the Test - Assembled
documentation for performing HST
Step 2: Voltage at Source and Polarity - Measured voltage at source before plugging in
