FDOT Final Estimates - Level 1 with correct answers 100%

FDOT Final Estimates - Level 1 with correct answers 100% What two types of Estimates are needed to pay for the work performed by contractors? - Correct Answers Final & Progress Monthly In case of discrepancies among the contract documents, which document takes the highest precedence? - Correct Answers Special Provisions Contractors Recieve progress payments on the basis of? - Correct Answers Monthly Progress Estimates Which of the following sets forth the Department's methods and procedures for preparing and checking final estimates? - Correct Answers Preparation and Documentation Manual (PDM) Which Document contains a series of Specially designed forms that show both original estimates of quantities and the final quantities as measured ad accepted? - Correct Answers Computation Books Which Document contains alignment notes, cross-section notes, linear and area measurements and dimension sketches? - Correct Answers Field Notebooks Where are major changes during construction documented and "as-built" conditions shown? - Correct Answers Field Notebooks What identification is needed to show on the front cover of a field book? - Correct Answers FEID, Contract number, General contents of the book When making corrections to a field book entry, you should: - Correct Answers strike through, initial and enter correct data and date What should be started on the first lined page (page 1) of a field book? - Correct Answers INDEX An entire page of a field notebook you are using is incorrect, what do you do to correct the situation? - Correct Answers Mark the page VOID and reference it to a new page showing the correct information. "Check Levels" must be run at the start of a construction project to assure that: - Correct Answers Construction will be done to design elevations & final measurements for payment will be from the same base elevations as the original survey. What should accompany final measurements so that nonstandard measurements may be interpreted accurately? - Correct Answers Sketches In the REMARKS column of most computation book forms a reference should be made to the: - Correct Answers Source Documents When is it permissible to record only the net weight on an asphaltic concrete tabulation form? - Correct Answers Never, gross tare must be included also A limerock base course is constructed in two 13-foot widths between station 19+40.20 and station 84+50.00. What is the area of the base course to the whole square yard? - Correct Answers 18,806 SY How many square yards are in one acre? - Correct Answers 4,840 Determine the area of the section (G) in the circle to the tenth of a square foot. (NOTE: A= pi r(squared) x (angle/360degrees) - Correct Answers 887.3 SF If you have a benchmark at an elevation of 80.25' and a back sight rob reading of 5.45', what is the height of instrument (HI)? - Correct Answers 85.70' If you have a pile cut off elevation of 50.00' and tip elevation of 10.00', what would your pile length be? - Correct Answers 40' Where can you find the typical widths of base and surface courses? - Correct Answers Typical Sections sheets of the plans Thirteen and one-half gallons is equal to how many cubic feet? - Correct Answers 1.8 Cubic Feet Using the data given below, find the volume to the nearest cubic yard. The areas were determined for the cross sections at these stations: Station: Area (Sq Feet): 5091+00 287.60 5091+38 302.0 5091+91 298.10 5092+47 295.50 5092+69 288.30 - Correct Answers 1,857 CY Determine the volume of the cone to the nearest hundredth of a cubic foot. - Correct Answers 42.03 CF Calculate the volume of the geometric shape to the nearest cubic yard: - Correct Answers 1,795 CY Most Linear pay items are measures in linear ________? - Correct Answers Feet Aside from measuring the length of fence, you should count and document the number of: - Correct Answers Corner post assemblies & pull and end post assemblies The various fencing post assemblies are identified by approximate ________ and are totaled in a ___________. - Correct Answers Station; field notbook You should be sure that the batch scales nd automatic printer at an asphalt plant are certified for accuracy every __________. - Correct Answers Six Months The accuracy of batch scales and automatic printers should be checked: - Correct Answers At least once a week & before accepting the first load on a project.