NCCCO Core Exam Outline UPDATED
ACTUAL Exam Questions and CORRECT
Answers
Timber or steel - CORRECT ANSWER - These materials should be used when setting up
on soft surfaces such as soft ground, asphalt or backfilled material
Over the corner - CORRECT ANSWER - On crawler cranes, which boom position creates
the greatest ground pressure
Blocking - CORRECT ANSWER - Allows the weight of the crane and load to be
distributed over a greater surface area. Should be used under outrigger floats at all times.
3 - CORRECT ANSWER - Blocking should be at least how many times the surface area of
the float
Energized - CORRECT ANSWER - Overhead power lines must be considered to be in this
condition until electrical authorities indicate otherwise
Prohibited zone - CORRECT ANSWER - No part of the crane or load must ever enter this
area around an energized power line
kV - CORRECT ANSWER - The prohibited zone must be enlarged as this increases
20 foot - CORRECT ANSWER - What minimum distance does OSHA require be
maintained when voltage up to 350 kV is unknown
50 foot - CORRECT ANSWER - What minimum distance is required if the voltage is over
350 kV and unknown
, Qualified signal person - CORRECT ANSWER - This person must be appointed any time
the crane is working within a boom's length of the prohibited zone
Tag lines - CORRECT ANSWER - The use of these should be avoided when lifting near
power lines, however if necessary should be non-conductive type
Above power lines - CORRECT ANSWER - Avoid operating cranes or handling materials
in this area of power lines
Remain in the cab - CORRECT ANSWER - What does an operator do if the crane comes
in contact with a power line
Jump - CORRECT ANSWER - If it is necessary to leave the crane cab before power lines
are de-energized after contact, how does the operator exit the cab
transmission towers - CORRECT ANSWER - A crane can also become electrically
charged when working close to these (radio, microwave, cell)
Manufacturer - CORRECT ANSWER - Before traveling on site with a load, be sure that
this is allowed by the
Backward collapse - CORRECT ANSWER - Ensure the boom low enough when traveling
with a load to avoid the possibility of this
Toward the load - CORRECT ANSWER - Always travel in this direction when traveling
with a load
Boom extension, jib, or pinned section - CORRECT ANSWER - Most manufacturers do
not permit travel with a load when the boom is in these settings
ACTUAL Exam Questions and CORRECT
Answers
Timber or steel - CORRECT ANSWER - These materials should be used when setting up
on soft surfaces such as soft ground, asphalt or backfilled material
Over the corner - CORRECT ANSWER - On crawler cranes, which boom position creates
the greatest ground pressure
Blocking - CORRECT ANSWER - Allows the weight of the crane and load to be
distributed over a greater surface area. Should be used under outrigger floats at all times.
3 - CORRECT ANSWER - Blocking should be at least how many times the surface area of
the float
Energized - CORRECT ANSWER - Overhead power lines must be considered to be in this
condition until electrical authorities indicate otherwise
Prohibited zone - CORRECT ANSWER - No part of the crane or load must ever enter this
area around an energized power line
kV - CORRECT ANSWER - The prohibited zone must be enlarged as this increases
20 foot - CORRECT ANSWER - What minimum distance does OSHA require be
maintained when voltage up to 350 kV is unknown
50 foot - CORRECT ANSWER - What minimum distance is required if the voltage is over
350 kV and unknown
, Qualified signal person - CORRECT ANSWER - This person must be appointed any time
the crane is working within a boom's length of the prohibited zone
Tag lines - CORRECT ANSWER - The use of these should be avoided when lifting near
power lines, however if necessary should be non-conductive type
Above power lines - CORRECT ANSWER - Avoid operating cranes or handling materials
in this area of power lines
Remain in the cab - CORRECT ANSWER - What does an operator do if the crane comes
in contact with a power line
Jump - CORRECT ANSWER - If it is necessary to leave the crane cab before power lines
are de-energized after contact, how does the operator exit the cab
transmission towers - CORRECT ANSWER - A crane can also become electrically
charged when working close to these (radio, microwave, cell)
Manufacturer - CORRECT ANSWER - Before traveling on site with a load, be sure that
this is allowed by the
Backward collapse - CORRECT ANSWER - Ensure the boom low enough when traveling
with a load to avoid the possibility of this
Toward the load - CORRECT ANSWER - Always travel in this direction when traveling
with a load
Boom extension, jib, or pinned section - CORRECT ANSWER - Most manufacturers do
not permit travel with a load when the boom is in these settings
