ISA CCST LEVEL III (ISA LEVEL III
STUDY GUIDE) QUESTIONS WITH
100% CORRECT ANSWERS!!
1 of 78
Term
When reading a mercury manometer, the center of the meniscus
should be?
Give this one a try later!
Planned maintenance Master list*
Repair maintenance* P&ID
Corrective maintenance Related instrument data sheet
Predictive maintenance Job specifications
, A. Operations test A. Higher than the outer edge
B.Visual inspection* *
C. Output wiring check B.Lower than the outer edge
D.Continuity test C. Same as the outer edge
D.Level to the outer edge
Don't know?
2 of 78
Term
All of the following are found on an Instrument Data Sheet EXCEPT:
A. Tag numbers
B.Manufacturers information
C. Pipe connection information
D.Calibration information
Give this one a try later!
A. On a specification form
B.On a P&ID
C. On a loop diagram
D.In a maintenance history file*
A. Tag numbers
B.Manufacturers information
C. Pipe connection information*
D.Calibration information
A. Data sheet
B.Installation detail
, C. P&ID*
D.Control schematic
A. It will yield good control regardless of process conditions
B.It eliminates the need for controller tuning by technicians
C. It is best suited for a process with variable gain
D.It is largely being replaced by adaptive gain controllers*
Don't know?
3 of 78
Definition
A. Convey all useful information about an instrument
B.Constitute a short form of specifications for an individual
instrument or instrument type
C. Contain necessary process data, physical maintenance
requirements, environmental conditions, electrical requirements, and
expected operational behavior for the instrument
D.All of the above*
Give this one a try later!
When removing a differential flow
Derivative control operates on____?
instrument with a liquid seal from
service,:
Processes characterized by
long deadtimes or short time Data sheets:
constants are:
, Don't know?
4 of 78
Term
A self tuning controller is particular useful for the following:
A. Regulating process
B.Non-regulating process
C. pH control from 6.8-7.2
D. pH control from 5 to 7*
Give this one a try later!
A. Regulating process A. relocating the transmitters
B.Non-regulating process and FCE
C. pH control from 6.8-7.2 B.reconfiguring the loop*
D. pH control from 5 to C. installing a UPS and inverter
7*
D.installing another CPU
A. non - linear process * A. Receiving instruments
B.high temperature B.Inspecting instruments
C. absolute pressure C. Tagging instruments
D.oscillating flow D.Calibrating Instruments*
Don't know?
5 of 78
Term
STUDY GUIDE) QUESTIONS WITH
100% CORRECT ANSWERS!!
1 of 78
Term
When reading a mercury manometer, the center of the meniscus
should be?
Give this one a try later!
Planned maintenance Master list*
Repair maintenance* P&ID
Corrective maintenance Related instrument data sheet
Predictive maintenance Job specifications
, A. Operations test A. Higher than the outer edge
B.Visual inspection* *
C. Output wiring check B.Lower than the outer edge
D.Continuity test C. Same as the outer edge
D.Level to the outer edge
Don't know?
2 of 78
Term
All of the following are found on an Instrument Data Sheet EXCEPT:
A. Tag numbers
B.Manufacturers information
C. Pipe connection information
D.Calibration information
Give this one a try later!
A. On a specification form
B.On a P&ID
C. On a loop diagram
D.In a maintenance history file*
A. Tag numbers
B.Manufacturers information
C. Pipe connection information*
D.Calibration information
A. Data sheet
B.Installation detail
, C. P&ID*
D.Control schematic
A. It will yield good control regardless of process conditions
B.It eliminates the need for controller tuning by technicians
C. It is best suited for a process with variable gain
D.It is largely being replaced by adaptive gain controllers*
Don't know?
3 of 78
Definition
A. Convey all useful information about an instrument
B.Constitute a short form of specifications for an individual
instrument or instrument type
C. Contain necessary process data, physical maintenance
requirements, environmental conditions, electrical requirements, and
expected operational behavior for the instrument
D.All of the above*
Give this one a try later!
When removing a differential flow
Derivative control operates on____?
instrument with a liquid seal from
service,:
Processes characterized by
long deadtimes or short time Data sheets:
constants are:
, Don't know?
4 of 78
Term
A self tuning controller is particular useful for the following:
A. Regulating process
B.Non-regulating process
C. pH control from 6.8-7.2
D. pH control from 5 to 7*
Give this one a try later!
A. Regulating process A. relocating the transmitters
B.Non-regulating process and FCE
C. pH control from 6.8-7.2 B.reconfiguring the loop*
D. pH control from 5 to C. installing a UPS and inverter
7*
D.installing another CPU
A. non - linear process * A. Receiving instruments
B.high temperature B.Inspecting instruments
C. absolute pressure C. Tagging instruments
D.oscillating flow D.Calibrating Instruments*
Don't know?
5 of 78
Term
