1
FANUC certification final exam . Questions and
Correct Answers. A+ GRADE GUARANTEED
Turning the Teach Pendant on: - (answers)Gives motion control solely to the
operator via the teach pendant
What must be accomplished to avoid hard-stops and over travels? -
(answers)Set Axis Limits
SHIFT and the hard key COORD will display the following menu: - (answers)The
"jog" menu
SHIFT and POINT are needed to do what? - (answers)Record the current
position of the robot
In the motion command "J P [2] 100% FINE", If you wanted to change the
"FINE" component to a "CNT100" what buttons would you press? -
(answers)Select component, then press [CHOICE]
To switch manually from one program to another, you have to be in which
screen? - (answers)Select
How many Robot I/O points are standard on a controller? - (answers)16
Which soft key is pressed to display the current motion instruction defaults
from the EDIT Screen? - (answers)POINT
When creating a program, which hard key should be pressed? - (answers)Select
, 2
When using the Prog Adjust utility, which statement is correct? -
(answers)Pressing CLR_ADJ or CLR_ALL will save the enabled data values
Which of the following tasks can be performed from the FILE Menu? -
(answers)Get a default directory of the device
If while jogging the robot, you get an "in singularity" error, What must you do?
- (answers)Joint jog J5 +/- at least 10 degrees
The"Program Header Information" at the DETAIL softkey enables you to modify
the following program information, EXCEPT: - (answers)Active tool frame
What position is the suggested type of motion used to move the robot to a
HOME position? - (answers)Joint
Which softkey allows you to enter additional program instructions into a teach
pendant program? - (answers)[INST]
Which of the following is a type of I/O signal? - (answers)Digital I/O
Which of the following hard keys would bring the menu item ABORT ALL to the
TP Screen? - (answers)FCTN
If you would like to look at the positional data of P[3] in the instruction "J P[3]
100% FINE", what buttons would you press? - (answers)Cursor to the 3 of P[3]
and press F5 POSITION
FANUC certification final exam . Questions and
Correct Answers. A+ GRADE GUARANTEED
Turning the Teach Pendant on: - (answers)Gives motion control solely to the
operator via the teach pendant
What must be accomplished to avoid hard-stops and over travels? -
(answers)Set Axis Limits
SHIFT and the hard key COORD will display the following menu: - (answers)The
"jog" menu
SHIFT and POINT are needed to do what? - (answers)Record the current
position of the robot
In the motion command "J P [2] 100% FINE", If you wanted to change the
"FINE" component to a "CNT100" what buttons would you press? -
(answers)Select component, then press [CHOICE]
To switch manually from one program to another, you have to be in which
screen? - (answers)Select
How many Robot I/O points are standard on a controller? - (answers)16
Which soft key is pressed to display the current motion instruction defaults
from the EDIT Screen? - (answers)POINT
When creating a program, which hard key should be pressed? - (answers)Select
, 2
When using the Prog Adjust utility, which statement is correct? -
(answers)Pressing CLR_ADJ or CLR_ALL will save the enabled data values
Which of the following tasks can be performed from the FILE Menu? -
(answers)Get a default directory of the device
If while jogging the robot, you get an "in singularity" error, What must you do?
- (answers)Joint jog J5 +/- at least 10 degrees
The"Program Header Information" at the DETAIL softkey enables you to modify
the following program information, EXCEPT: - (answers)Active tool frame
What position is the suggested type of motion used to move the robot to a
HOME position? - (answers)Joint
Which softkey allows you to enter additional program instructions into a teach
pendant program? - (answers)[INST]
Which of the following is a type of I/O signal? - (answers)Digital I/O
Which of the following hard keys would bring the menu item ABORT ALL to the
TP Screen? - (answers)FCTN
If you would like to look at the positional data of P[3] in the instruction "J P[3]
100% FINE", what buttons would you press? - (answers)Cursor to the 3 of P[3]
and press F5 POSITION
