1
CSWA
CSWA solidworks certification Exam
Questions with Correct Verified
Solutions 100% Guaranteed Pass
Before starting the exam: - ANS ✓Open SolidWorks, open new part file,
set units, and set material.
Used in SOLIDWORKS in both Sketches and Features to control the
value of a dimension. - ANS ✓Global Variables
A single view based on a predefined view orientation. - ANS ✓Model
View
A projected view is an orthographic projection of a parent view at 90
degrees. (Right, Top, Left, B - ANS ✓Projected View
An auxiliary view is a projected view that is normal to a reference
edge. - ANS ✓Auxiliary View
Created by cutting the parent view using a section line in order to see
inside details. - ANS ✓Section View
A section view that does not cut through the entire model. - ANS
✓Partial Section View
CSWA solidworks certification
, 2
CSWA
Special types of section views that allow you to show details of a
section created at an angle. - ANS ✓Aligned Section View
______are commonly used for drawing with rotational symmetry such
as wheels or flanges that have holes or other features arrayed in a
circular pattern. - ANS ✓Aligned Section View
In an aligned section view, if a standard section line cannot be drawn
vertically or horizontally to go through the center of a feature
then______ is used that does not line up with the parent view.: - ANS
✓angled section line
: Cut away a portion of an assembly in order to expose the inside.
emplate. - ANS ✓Broken-Out Section View
: Show portions of a model that are difficult to see in the parent view. -
ANS ✓Detail View
: Define views by selecting any face from the model that does not
require a parent view or have a view arrow. - ANS ✓Relative to Model
View
: Create a break/gap in a model so that the view can fit on a smaller
drawing sheet. - ANS ✓Break View
: Creates 3 default orthographic views of the model (Top, Front, Right
Side). - ANS ✓Standard 2 View
CSWA solidworks certification
CSWA
CSWA solidworks certification Exam
Questions with Correct Verified
Solutions 100% Guaranteed Pass
Before starting the exam: - ANS ✓Open SolidWorks, open new part file,
set units, and set material.
Used in SOLIDWORKS in both Sketches and Features to control the
value of a dimension. - ANS ✓Global Variables
A single view based on a predefined view orientation. - ANS ✓Model
View
A projected view is an orthographic projection of a parent view at 90
degrees. (Right, Top, Left, B - ANS ✓Projected View
An auxiliary view is a projected view that is normal to a reference
edge. - ANS ✓Auxiliary View
Created by cutting the parent view using a section line in order to see
inside details. - ANS ✓Section View
A section view that does not cut through the entire model. - ANS
✓Partial Section View
CSWA solidworks certification
, 2
CSWA
Special types of section views that allow you to show details of a
section created at an angle. - ANS ✓Aligned Section View
______are commonly used for drawing with rotational symmetry such
as wheels or flanges that have holes or other features arrayed in a
circular pattern. - ANS ✓Aligned Section View
In an aligned section view, if a standard section line cannot be drawn
vertically or horizontally to go through the center of a feature
then______ is used that does not line up with the parent view.: - ANS
✓angled section line
: Cut away a portion of an assembly in order to expose the inside.
emplate. - ANS ✓Broken-Out Section View
: Show portions of a model that are difficult to see in the parent view. -
ANS ✓Detail View
: Define views by selecting any face from the model that does not
require a parent view or have a view arrow. - ANS ✓Relative to Model
View
: Create a break/gap in a model so that the view can fit on a smaller
drawing sheet. - ANS ✓Break View
: Creates 3 default orthographic views of the model (Top, Front, Right
Side). - ANS ✓Standard 2 View
CSWA solidworks certification
