Boilermaker test
The fumes produced during welding upon which of the materials listed below pose a health hazard -
Galvanized , carbon steel, stainless steel
During the air carbon arc cutting process , jets of compressed air are used to blow the slag away from the
cuts area. Which are the potential hazards during this process - Thermal burns, burning holes in
compressed air line, burnt shoes and clothing
What do you do with a socket that has cracks - Mark the socket with yellow paint and discard it
immediately
What is the tower man way used for - To enter the tower internally
The proper tightening sequence for a flange is a _______ pattern - Cross bolting
What wrench size do you use on 3/4 stud with heavy hex nuts - 1-1/4
When rigging valves , you should rig by the - Body
Where the hydrostatic testing goes - Bottom with the tiny circle and cross in a middle 2
Where is the man way - You enter in the hole-D
Bonnet bell head - The very top of the tower -8
When blinding a tower, what is the most preferred placement of the blinds - At first flagnge of the
tower, at the top of the tower, the easiest place to install them, or neither
A ring type joint (RTJ) flange would be used in a - High pressure pipe work system
, When hydro testing process equipment , where should the vent be located - At the highest point
allowed to relieve air pressure
What should be done when performing a first line break - Break away and down from you
Pass partition - Line in the middle of the bottom of the tower - 3
Channel head - Right side of the tower lower -10
Tubes - Middle of tower inside - 6
Davit - Skinny tube on the right side - B
Where are the bubble caps located - On the tray rings
The use of #9 wire as a socket retainer is permitted - False
The channel head cover and dollar plate are considered as the same terminology - True
What does the tray floor attach to - The tray ring
A process valve that automatically opens to prevent over pressure of a system is referred to as a -
Control
Floating head - Under bell head 9
Fixed tube sheet - 4 under tubes
The fumes produced during welding upon which of the materials listed below pose a health hazard -
Galvanized , carbon steel, stainless steel
During the air carbon arc cutting process , jets of compressed air are used to blow the slag away from the
cuts area. Which are the potential hazards during this process - Thermal burns, burning holes in
compressed air line, burnt shoes and clothing
What do you do with a socket that has cracks - Mark the socket with yellow paint and discard it
immediately
What is the tower man way used for - To enter the tower internally
The proper tightening sequence for a flange is a _______ pattern - Cross bolting
What wrench size do you use on 3/4 stud with heavy hex nuts - 1-1/4
When rigging valves , you should rig by the - Body
Where the hydrostatic testing goes - Bottom with the tiny circle and cross in a middle 2
Where is the man way - You enter in the hole-D
Bonnet bell head - The very top of the tower -8
When blinding a tower, what is the most preferred placement of the blinds - At first flagnge of the
tower, at the top of the tower, the easiest place to install them, or neither
A ring type joint (RTJ) flange would be used in a - High pressure pipe work system
, When hydro testing process equipment , where should the vent be located - At the highest point
allowed to relieve air pressure
What should be done when performing a first line break - Break away and down from you
Pass partition - Line in the middle of the bottom of the tower - 3
Channel head - Right side of the tower lower -10
Tubes - Middle of tower inside - 6
Davit - Skinny tube on the right side - B
Where are the bubble caps located - On the tray rings
The use of #9 wire as a socket retainer is permitted - False
The channel head cover and dollar plate are considered as the same terminology - True
What does the tray floor attach to - The tray ring
A process valve that automatically opens to prevent over pressure of a system is referred to as a -
Control
Floating head - Under bell head 9
Fixed tube sheet - 4 under tubes
