Woodshop safety test Exam Questions & Answers 2023|2024
Safety instructions must be given before you are allowed to work on or operate
any machine or _______ - ANSWER-tool you are not permitted to work on any
equipment or machine if the ______ is not present - ANSWER-instructor guards
and safety device must be on all machines during _____ - ANSWER-operation
machinery must not be oiled or adjusted while in ____ - ANSWER-use a machine
must be started and stopped only by the _____ - ANSWER-operator do not leave
a machine while it is _____ - ANSWER-running when working on or near any
machine or tool where there is a possibility of eye injury, you must wear _____ -
ANSWER-eye protection you are not permitted within the safety zone around
any machine unless you are the _____ - ANSWER-operator loose clothing must
be tucked in before you start work as a precaution against _____ - ANSWER-
getting entangled if in doubt about a machine check with the _____ - ANSWER-
instructor asiles and working areas but be kept clear of ____ - ANSWER-all
obstructions The shop floor must be kept free of oil because of the danger of
fire and _____ - ANSWER-slipping combustible rags must be kept in a closed
_____ - ANSWER-red container do not lift materials heavier than your ability to
handle them ____ - ANSWER-safely long pieces of material should be carried by
____ - ANSWER-2 people the attention of the instructor should be direction to
any violation of ____ - ANSWER-the rules accidents no matter how slight must
be reported immediately to _____ - ANSWER-the instructor Carry sharp pointed
tools pointed _____ - ANSWER-downward do not leave tools and materials ____
from a vice or bench - ANSWER-clamped a dull tool is dangerous because it will
____ - ANSWER-skip passed tools to classmates with the tool handles _____ -
ANSWER-towards them do not stand in front of anyone using a sharp _____ -
ANSWER-tool carry a hand saw buy the handle with the toe ____ - ANSWER-
pointed downward when using a screwdriver, avoid holding the material in the
____ - ANSWER-hand after clamps have been applied to the work, it should not
be ____ - ANSWER-moved face shields or googles/glasses must be work but
students when there is a possibility of _____ - ANSWER-loose debris whenever
possible, the _____ should be clamped - ANSWER-project stock all adjustments
should be made before the machine is ____ - ANSWER-turned on the operator
must keep his/her fingers away from the _____ spindle chuck, and but -
ANSWER-spinning when operating the drill press, _____ the material instead of
holding it by hand - ANSWER-clamp before turning on the power, the chuck key
should be ____ - ANSWER-removed when the drill begins to break through the
work you should ease up on the ____ - ANSWER-forward pressure chips should
be removed from the drill press table when the machine is ____ - ANSWER-
turned off when the drill is being tightened in the chuck, the cord should be
____ - ANSWER-unplugged the operator should be ready to stop the ____
instantly - ANSWER-machine to prevent the work from being caught, the tool
rest must be kept within _____ of the grinding wheel - ANSWER-1/8 of an inch
grinding on the _____ of the wheel may produce pressure which can cause the
wheel to break - ANSWER-edge or side when using the buffer, the operator
must use ____ to control the work being buffed - ANSWER-both hands the
shortest length of stock which may be run over the jointer safely is _____ -
ANSWER-12 inches when face planning stock, the operator must always use a
_____ - ANSWER-*we don't do that here* when face planning, always allow the
guard to swing back over the knives before removing the _____ - ANSWER-*we
Safety instructions must be given before you are allowed to work on or operate
any machine or _______ - ANSWER-tool you are not permitted to work on any
equipment or machine if the ______ is not present - ANSWER-instructor guards
and safety device must be on all machines during _____ - ANSWER-operation
machinery must not be oiled or adjusted while in ____ - ANSWER-use a machine
must be started and stopped only by the _____ - ANSWER-operator do not leave
a machine while it is _____ - ANSWER-running when working on or near any
machine or tool where there is a possibility of eye injury, you must wear _____ -
ANSWER-eye protection you are not permitted within the safety zone around
any machine unless you are the _____ - ANSWER-operator loose clothing must
be tucked in before you start work as a precaution against _____ - ANSWER-
getting entangled if in doubt about a machine check with the _____ - ANSWER-
instructor asiles and working areas but be kept clear of ____ - ANSWER-all
obstructions The shop floor must be kept free of oil because of the danger of
fire and _____ - ANSWER-slipping combustible rags must be kept in a closed
_____ - ANSWER-red container do not lift materials heavier than your ability to
handle them ____ - ANSWER-safely long pieces of material should be carried by
____ - ANSWER-2 people the attention of the instructor should be direction to
any violation of ____ - ANSWER-the rules accidents no matter how slight must
be reported immediately to _____ - ANSWER-the instructor Carry sharp pointed
tools pointed _____ - ANSWER-downward do not leave tools and materials ____
from a vice or bench - ANSWER-clamped a dull tool is dangerous because it will
____ - ANSWER-skip passed tools to classmates with the tool handles _____ -
ANSWER-towards them do not stand in front of anyone using a sharp _____ -
ANSWER-tool carry a hand saw buy the handle with the toe ____ - ANSWER-
pointed downward when using a screwdriver, avoid holding the material in the
____ - ANSWER-hand after clamps have been applied to the work, it should not
be ____ - ANSWER-moved face shields or googles/glasses must be work but
students when there is a possibility of _____ - ANSWER-loose debris whenever
possible, the _____ should be clamped - ANSWER-project stock all adjustments
should be made before the machine is ____ - ANSWER-turned on the operator
must keep his/her fingers away from the _____ spindle chuck, and but -
ANSWER-spinning when operating the drill press, _____ the material instead of
holding it by hand - ANSWER-clamp before turning on the power, the chuck key
should be ____ - ANSWER-removed when the drill begins to break through the
work you should ease up on the ____ - ANSWER-forward pressure chips should
be removed from the drill press table when the machine is ____ - ANSWER-
turned off when the drill is being tightened in the chuck, the cord should be
____ - ANSWER-unplugged the operator should be ready to stop the ____
instantly - ANSWER-machine to prevent the work from being caught, the tool
rest must be kept within _____ of the grinding wheel - ANSWER-1/8 of an inch
grinding on the _____ of the wheel may produce pressure which can cause the
wheel to break - ANSWER-edge or side when using the buffer, the operator
must use ____ to control the work being buffed - ANSWER-both hands the
shortest length of stock which may be run over the jointer safely is _____ -
ANSWER-12 inches when face planning stock, the operator must always use a
_____ - ANSWER-*we don't do that here* when face planning, always allow the
guard to swing back over the knives before removing the _____ - ANSWER-*we
