Woodshop safety Exam Questions and Answers 100% Correct
Safety instructions must be given before you are allowed to work on or operate
any machine or ______. - ANSWER-tool You are not permitted to work on any
equipment or machine if the ________ is not present. - ANSWER-teacher Guards
and safety devices must be on all machines during ______. - ANSWER-operation
Machinery must not be oiled or adjusted while in ______. - ANSWER-use A
machine must be started and stopped only by the ______. - ANSWER-operator
Do not leave a machine while it is ______. - ANSWER-running When working on
or near any machine or tool where there is a possibility of eye injury, you must
wear _________. - ANSWER-eye protection You are not permitted within the
safety zone around any machine unless you are the ________. - ANSWER-
operator Loose clothing must be tucked in before you start work, as a
precaution against __________. - ANSWER-getting caught/entangled If in doubt
about any machine, check with the ________. - ANSWER-Teacher Aisles and
working areas must be kept clear of ___________. - ANSWER-all obstructions The
shop floor must be kept free of oil because of the danger of fire and ________. -
ANSWER-slipping Combustible rags must be kept in a closed __________. -
ANSWER-red container Do not lift materials heavier than your ability to handle
them ________. - ANSWER-safely Long pieces of material should be carried by
________. - ANSWER-2 people The attention of the teacher should be directed to
any violation of _____. - ANSWER-rules Accidents no matter how slight, must be
reported immediately to ___________. - ANSWER-the instructor Carry sharp
pointed tools pointed ________. - ANSWER-downward Do not leave tools and
materials ________ from a vice or a bench. - ANSWER-clamped A dull tool is
dangerous because it will _____. - ANSWER-skip Pass tools to classmates with
the tool handles ____________. - ANSWER-pointing towards them Do not stand in
front of anyone using a sharp ______. - ANSWER-tool Carry a hand saw by the
handle with the toe __________. - ANSWER-pointed downward When using a
screwdriver, avoid holding the material in the _______. - ANSWER-hand After
clamps have been applied to the work, it should not be ________. - ANSWER-
moved Face shields or goggles/glasses must be worn by shop students when
there is a possibility of __________. - ANSWER-loose debris Whenever possible,
the ________ should be clamped. - ANSWER-project stock All adjustments should
be made before the machine is ________. - ANSWER-turned on The operator
must keep his/her fingers away from the _______ spindle, chuck, and bit. -
ANSWER-spinning When operating the drill press, ______ the material instead of
holding it by hand. - ANSWER-clamp Before turning on the power, the chuck
key should be __________. - ANSWER-removed from the chuck When the drill
begins to break through the work you should ease up on the ________. -
ANSWER-forward pressure Chips should be removed from the drill press table
when the machine is _________. - ANSWER-turned off When the drill is being
tightened in the chuck, the cord should be _______. - ANSWER-unplugged The
operator should be ready to stop the _______ instantly. - ANSWER-machine To
prevent the work from being caught, the tool rest must be kept within ________
of the grinding wheel. - ANSWER-1/8" Grinding on the ______ of the wheel may
produce pressure which can cause the wheel to break. - ANSWER-edge When
using the buffer, the operator must use ______ to control the work being buffed.
- ANSWER-both hands The shortest length of stock which may be run over the
jointer safely is _______. - ANSWER-12" When face planning stock, the operator
Safety instructions must be given before you are allowed to work on or operate
any machine or ______. - ANSWER-tool You are not permitted to work on any
equipment or machine if the ________ is not present. - ANSWER-teacher Guards
and safety devices must be on all machines during ______. - ANSWER-operation
Machinery must not be oiled or adjusted while in ______. - ANSWER-use A
machine must be started and stopped only by the ______. - ANSWER-operator
Do not leave a machine while it is ______. - ANSWER-running When working on
or near any machine or tool where there is a possibility of eye injury, you must
wear _________. - ANSWER-eye protection You are not permitted within the
safety zone around any machine unless you are the ________. - ANSWER-
operator Loose clothing must be tucked in before you start work, as a
precaution against __________. - ANSWER-getting caught/entangled If in doubt
about any machine, check with the ________. - ANSWER-Teacher Aisles and
working areas must be kept clear of ___________. - ANSWER-all obstructions The
shop floor must be kept free of oil because of the danger of fire and ________. -
ANSWER-slipping Combustible rags must be kept in a closed __________. -
ANSWER-red container Do not lift materials heavier than your ability to handle
them ________. - ANSWER-safely Long pieces of material should be carried by
________. - ANSWER-2 people The attention of the teacher should be directed to
any violation of _____. - ANSWER-rules Accidents no matter how slight, must be
reported immediately to ___________. - ANSWER-the instructor Carry sharp
pointed tools pointed ________. - ANSWER-downward Do not leave tools and
materials ________ from a vice or a bench. - ANSWER-clamped A dull tool is
dangerous because it will _____. - ANSWER-skip Pass tools to classmates with
the tool handles ____________. - ANSWER-pointing towards them Do not stand in
front of anyone using a sharp ______. - ANSWER-tool Carry a hand saw by the
handle with the toe __________. - ANSWER-pointed downward When using a
screwdriver, avoid holding the material in the _______. - ANSWER-hand After
clamps have been applied to the work, it should not be ________. - ANSWER-
moved Face shields or goggles/glasses must be worn by shop students when
there is a possibility of __________. - ANSWER-loose debris Whenever possible,
the ________ should be clamped. - ANSWER-project stock All adjustments should
be made before the machine is ________. - ANSWER-turned on The operator
must keep his/her fingers away from the _______ spindle, chuck, and bit. -
ANSWER-spinning When operating the drill press, ______ the material instead of
holding it by hand. - ANSWER-clamp Before turning on the power, the chuck
key should be __________. - ANSWER-removed from the chuck When the drill
begins to break through the work you should ease up on the ________. -
ANSWER-forward pressure Chips should be removed from the drill press table
when the machine is _________. - ANSWER-turned off When the drill is being
tightened in the chuck, the cord should be _______. - ANSWER-unplugged The
operator should be ready to stop the _______ instantly. - ANSWER-machine To
prevent the work from being caught, the tool rest must be kept within ________
of the grinding wheel. - ANSWER-1/8" Grinding on the ______ of the wheel may
produce pressure which can cause the wheel to break. - ANSWER-edge When
using the buffer, the operator must use ______ to control the work being buffed.
- ANSWER-both hands The shortest length of stock which may be run over the
jointer safely is _______. - ANSWER-12" When face planning stock, the operator
