Wood Shop Safety Test Study Guide Exam Questions and Answers 100%
correct
What is the margin of safety? - ANSWER-4 inches. When using a saw, never... -
ANSWER-Feed the material faster than the saw blade can remove the wood
easily. The palm sander is used for what? - ANSWER-removing small amounts of
material slowly. All small work should be secured with what? - ANSWER-A clamp
or vise. Make all adjustments on all power tools with the power off, except... -
ANSWER-When adjusting the speed of the lathe. Always cut.. - ANSWER-Away
from yourself when using a chisel, knife or any edged tool. What does it mean
when your wood chips are burnt when you are drilling? - ANSWER-Your drill bit
is dull. The shortest board that can be safely run through the planer is... -
ANSWER-12 inches. The belt sander is used for what? - ANSWER-removing large
amounts of material fast. The power miter box is used for what? - ANSWER-
Cutting angles, bevels, and crosscutting. The most material you can take off on
the planer at one time is... - ANSWER-One turn per pass. How long does the
board have to be to run through the performax sander? - ANSWER-12 inches
long. Then widest board that can be run through the planer is... - ANSWER-16
inches. When crosscutting on the table saw you should use what? - ANSWER-
The miter gauge. When ripping on the table saw you should use the... -
ANSWER-rip fence. The most you can take off with the performax sander per
pass is... - ANSWER-1/8 of a turn. You should never reach behind or in front of...
- ANSWER-The blade on the power miter box. The blade on the table saw should
extend about... - ANSWER-1/8" above the material when making a through cut.
When using a band saw, how should you make turns? - ANSWER-Make turns
carefully and do not bend the blade. When using a band saw, what does it
mean if you hear a clicking or screeching sound? - ANSWER-The blade is bent or
broken. When using a band saw, what type of cuts should you use to make
sharp curves? - ANSWER-Make relief cuts. The guard on the band saw should be
set... - ANSWER-1/8" to 1/4" above the material you are cutting. What is the
chuck key used for? - ANSWER-To change the bits in the drill press. It is not ok
to drill without... - ANSWER-Having the material clamped securely. The person
helping the operator of the table saw must only... - ANSWER-Float the board not
push or pull it. When using the table saw it is never ok to... - ANSWER-Free
hand a board which means cutting without the use of the fence or miter gauge.
When using the table saw never set anything on... - ANSWER-The left side of
the fence. The stock must rest flat on the... - ANSWER-surface of the machine
you are using. What should you use to clear scrap by the blade? - ANSWER-A
push stick. The stock does have to be... - ANSWER-Jointed or surfaced before
making a rip cut with a board. When using the router, the bit must not be
touching... - ANSWER-The surface before you start the router. When using the
table saw, always check the... - ANSWER-The height of the blade to make sure
the blade goes through the wood. Never place your hands in the... - ANSWER-
Cutting path of the blade. Before walking away from any machine,... - ANSWER-
Make sure it stops all motion. When you are sawing, relieve... - ANSWER-your
feed pressure as you reach the end of your saw cut. Never stand in the line of
fire on any machine due to... - ANSWER-Kick back. If the material is small,... -
ANSWER-You should use push sticks to aid in feeding the stock. When using the
planer the initial adjustment for the machine is made while it is off... - ANSWER-
All other adjustments are made while running. When using any equipment,
correct
What is the margin of safety? - ANSWER-4 inches. When using a saw, never... -
ANSWER-Feed the material faster than the saw blade can remove the wood
easily. The palm sander is used for what? - ANSWER-removing small amounts of
material slowly. All small work should be secured with what? - ANSWER-A clamp
or vise. Make all adjustments on all power tools with the power off, except... -
ANSWER-When adjusting the speed of the lathe. Always cut.. - ANSWER-Away
from yourself when using a chisel, knife or any edged tool. What does it mean
when your wood chips are burnt when you are drilling? - ANSWER-Your drill bit
is dull. The shortest board that can be safely run through the planer is... -
ANSWER-12 inches. The belt sander is used for what? - ANSWER-removing large
amounts of material fast. The power miter box is used for what? - ANSWER-
Cutting angles, bevels, and crosscutting. The most material you can take off on
the planer at one time is... - ANSWER-One turn per pass. How long does the
board have to be to run through the performax sander? - ANSWER-12 inches
long. Then widest board that can be run through the planer is... - ANSWER-16
inches. When crosscutting on the table saw you should use what? - ANSWER-
The miter gauge. When ripping on the table saw you should use the... -
ANSWER-rip fence. The most you can take off with the performax sander per
pass is... - ANSWER-1/8 of a turn. You should never reach behind or in front of...
- ANSWER-The blade on the power miter box. The blade on the table saw should
extend about... - ANSWER-1/8" above the material when making a through cut.
When using a band saw, how should you make turns? - ANSWER-Make turns
carefully and do not bend the blade. When using a band saw, what does it
mean if you hear a clicking or screeching sound? - ANSWER-The blade is bent or
broken. When using a band saw, what type of cuts should you use to make
sharp curves? - ANSWER-Make relief cuts. The guard on the band saw should be
set... - ANSWER-1/8" to 1/4" above the material you are cutting. What is the
chuck key used for? - ANSWER-To change the bits in the drill press. It is not ok
to drill without... - ANSWER-Having the material clamped securely. The person
helping the operator of the table saw must only... - ANSWER-Float the board not
push or pull it. When using the table saw it is never ok to... - ANSWER-Free
hand a board which means cutting without the use of the fence or miter gauge.
When using the table saw never set anything on... - ANSWER-The left side of
the fence. The stock must rest flat on the... - ANSWER-surface of the machine
you are using. What should you use to clear scrap by the blade? - ANSWER-A
push stick. The stock does have to be... - ANSWER-Jointed or surfaced before
making a rip cut with a board. When using the router, the bit must not be
touching... - ANSWER-The surface before you start the router. When using the
table saw, always check the... - ANSWER-The height of the blade to make sure
the blade goes through the wood. Never place your hands in the... - ANSWER-
Cutting path of the blade. Before walking away from any machine,... - ANSWER-
Make sure it stops all motion. When you are sawing, relieve... - ANSWER-your
feed pressure as you reach the end of your saw cut. Never stand in the line of
fire on any machine due to... - ANSWER-Kick back. If the material is small,... -
ANSWER-You should use push sticks to aid in feeding the stock. When using the
planer the initial adjustment for the machine is made while it is off... - ANSWER-
All other adjustments are made while running. When using any equipment,
