Woodshop Safety Test Questions & Answers with complete solutions
Safety instructions must be given before you are allowed to work on or operate
any machine or - ANSWER-tool You are not permitted to work on any equipment
or machine if the ____________________ is not present - ANSWER-instructor
Guards and safety devices must be on all machines during - ANSWER-operation
Machinery must not be oiled or adjusted while in - ANSWER-use A machine
must be started and stopped only by the - ANSWER-operator Do not leave a
machine while it is - ANSWER-running When working on or near an machine or
tool where there is a possibility of eye injury, you must wear - ANSWER-eye
protection You are not permitted within the safety zone around any machine
unless you are the - ANSWER-operator loose clothing must be tucked in before
you start work, as a precaution against - ANSWER-getting entangled If in doubt
about any machine, check with the - ANSWER-instructor Aisles and working
areas must be kept clear of - ANSWER-all obstructions The shop floor must be
kept free of oil because of the danger of fire and - ANSWER-slipping
Combustible rags must be kept in a closed - ANSWER-red container Do not lift
materials heavier than your ability to handle them - ANSWER-safely Long
pieces of material should be carried by - ANSWER-2 people The attention of the
instructor should be directed to any violation of - ANSWER-rules Accidents, no
matter how slight, must be reported immediately to - ANSWER-the instructor
carry sharp-pointed tools pointed - ANSWER-downward do not leave tools and
materials ____________ from a vise or a bench. - ANSWER-clamped A dull tool is
dangerous because it will - ANSWER-skip Pass tools to classmates with the tool
handles - ANSWER-toward them Do not stand in front of anyone using a sharp -
ANSWER-tool Carry a hand saw by the handle with the toe - ANSWER-pointed
downward When using a screwdriver, avoid holding the material in the -
ANSWER-hand After clamps have been applied to the work, it should not be -
ANSWER-moved Face shields or googles/glasses must be worn by shop
students when there is a possibility of - ANSWER-loose debris Whenever
possible, the _________ should be clamped - ANSWER-project stock All
adjustments should be made before the machine is - ANSWER-turned on The
operator must keep his/her fingers away from the ________spindle, chuck, and
bit. - ANSWER-spinning When operating the drill press, _________the material
instead of holding it by hand - ANSWER-clamp Before turning on the power, the
chuck key should be _______ - ANSWER-removed from the chuck When the drill
begins to break through the work you should ease up on the - ANSWER-forward
pressure Chips should be removed from the drill press table when the machine
is - ANSWER-turned off When the drill is being tightened in the chuck, the cord
should be - ANSWER-unplugged The operator should be ready to stop the
________ instantly - ANSWER-machine To prevent the work from being caught,
the tool rest must be kept within _____________ of the grinding wheel. -
ANSWER-1/8" Grinding on the ___________ of the wheel may produce pressure
which can cause the wheel to break - ANSWER-edge or side When using the
buffer, the operator must use ______________ to control the work being buffed. -
ANSWER-both hands The shortest length of stock wich may be run over the
jointer safely is - ANSWER-12" When face planning stock, the operator must
always use a - ANSWER-"we dont use that here" When face planning, always
allow the guard to swng back over the knives before removing the _________ -
ANSWER-"we dont do that here" When adjusting the depth of the cut, limit the
Safety instructions must be given before you are allowed to work on or operate
any machine or - ANSWER-tool You are not permitted to work on any equipment
or machine if the ____________________ is not present - ANSWER-instructor
Guards and safety devices must be on all machines during - ANSWER-operation
Machinery must not be oiled or adjusted while in - ANSWER-use A machine
must be started and stopped only by the - ANSWER-operator Do not leave a
machine while it is - ANSWER-running When working on or near an machine or
tool where there is a possibility of eye injury, you must wear - ANSWER-eye
protection You are not permitted within the safety zone around any machine
unless you are the - ANSWER-operator loose clothing must be tucked in before
you start work, as a precaution against - ANSWER-getting entangled If in doubt
about any machine, check with the - ANSWER-instructor Aisles and working
areas must be kept clear of - ANSWER-all obstructions The shop floor must be
kept free of oil because of the danger of fire and - ANSWER-slipping
Combustible rags must be kept in a closed - ANSWER-red container Do not lift
materials heavier than your ability to handle them - ANSWER-safely Long
pieces of material should be carried by - ANSWER-2 people The attention of the
instructor should be directed to any violation of - ANSWER-rules Accidents, no
matter how slight, must be reported immediately to - ANSWER-the instructor
carry sharp-pointed tools pointed - ANSWER-downward do not leave tools and
materials ____________ from a vise or a bench. - ANSWER-clamped A dull tool is
dangerous because it will - ANSWER-skip Pass tools to classmates with the tool
handles - ANSWER-toward them Do not stand in front of anyone using a sharp -
ANSWER-tool Carry a hand saw by the handle with the toe - ANSWER-pointed
downward When using a screwdriver, avoid holding the material in the -
ANSWER-hand After clamps have been applied to the work, it should not be -
ANSWER-moved Face shields or googles/glasses must be worn by shop
students when there is a possibility of - ANSWER-loose debris Whenever
possible, the _________ should be clamped - ANSWER-project stock All
adjustments should be made before the machine is - ANSWER-turned on The
operator must keep his/her fingers away from the ________spindle, chuck, and
bit. - ANSWER-spinning When operating the drill press, _________the material
instead of holding it by hand - ANSWER-clamp Before turning on the power, the
chuck key should be _______ - ANSWER-removed from the chuck When the drill
begins to break through the work you should ease up on the - ANSWER-forward
pressure Chips should be removed from the drill press table when the machine
is - ANSWER-turned off When the drill is being tightened in the chuck, the cord
should be - ANSWER-unplugged The operator should be ready to stop the
________ instantly - ANSWER-machine To prevent the work from being caught,
the tool rest must be kept within _____________ of the grinding wheel. -
ANSWER-1/8" Grinding on the ___________ of the wheel may produce pressure
which can cause the wheel to break - ANSWER-edge or side When using the
buffer, the operator must use ______________ to control the work being buffed. -
ANSWER-both hands The shortest length of stock wich may be run over the
jointer safely is - ANSWER-12" When face planning stock, the operator must
always use a - ANSWER-"we dont use that here" When face planning, always
allow the guard to swng back over the knives before removing the _________ -
ANSWER-"we dont do that here" When adjusting the depth of the cut, limit the
