NACE CIP1: Standards Questions and Answers 100% Verified

NACE CIP1: Standards Questions and Answers 100% Verified NACE No. 1/SSPC-SP 5 White Metal Blast Cleaning; free from all visible mill scale, rust, and coatings with 0% staining NACE No. 2/SSPC-SP 10 Near White Metal Blast Cleaning; free from all visible mill scale, rust, coatings with 5% staining allowed NACE No. 3/SSPC-SP 6 Commercial Blast Cleaning; free from all visible mill scale, rust, coatings with 33% staining allowed NACE No. 8/SSPC-SP 14 Industrial Blast Cleaning; allows tightly adherent mill scale, rust, and coatings on 10% of each unit area NACE No. 4/SSPC-SP 7 Brush Off Blast Cleaning; all tightly adherent mill scale, rust, and coatings can remain but all loosely adherent must be removed Sa 3 Blast Cleaning to Visually Clean Steel Sa 2 1/2 Very Thorough Blast Cleaning Sa 2 Thorough Blast Cleaning Sa 1 Light Blast Cleaning St 2 Thorough Hand and Power Tool Cleaning St 3 Very Thorough Hand and Power Tool Cleaning SSPC-SP 2 Hand Tool Cleaning; removes all loose mill scale, rust, and coatings SSPC-SP 3 Power Tool Cleaning; removes all loose mill scale, rust, and coatings SSPC-SP 15 Commercial Grade Power Tool Cleaning; removes all tightly adherent mill scale, rust, and coatings but allows staining on up to 33% of unit area w/ minimum 1 mil surface profile SSPC-SP 11 Power Tool Cleaning to Bare Metal; removes all tightly adherent mill scale, rust, and coatings w/ minimum 1 mil surface profile SSPC-SP 16 Brush-Off Blast Cleaning of Coated and Uncoated Galvanized Steel, Stainless Steels, and Non-Ferrous Metals NACE SP0178 Addresses design, fabrication, and surface finishing (i.e. smoothing welds/rounding edges) SSPC-SP 1 Solvent Cleaning; the only commonly used standard that formally governs solvent cleaning SSPC-VIS 3 SP visual guides and standards for power tool cleaning; initial rust grade before surface prep ASTM D 4285 Test Method for Indicating Oil or Water in Compressed Air "Blotter Test" SSPC-VIS 1 Guide and Reference Photographs for Steel Surfaces Prepared by Dry Abrasive Blast Cleaning ISO 8501-1 Visual guide to rust grades before surface preparation WJ-1 Waterjetting Clean to Bare Substrate; allows 0% tightly adhered mill scale, rust, and coatings WJ-2 Waterjetting allowing 5% tightly adhered mill scale, rust, and coatings WJ-3 Waterjetting allowing 33% tightly adhered mill scale, rust, and coatings WJ-4 Waterjetting allowing tightly adhered mill scale, rust, and coatings ISO 8502-3 Detecting dust on the substrate by pressing a clear tape to the surface, removing it, and noting the amount of dust ASTM C 136 Sieve Test; enables the inspector to measure the particle size and distribution of the abrasive ASTM D 4417 Standard test methods for field measurement of surface profile of Blast cleaned steel; Method A: Iso Comparator; Method B: Electronic Gauge; Method C: Profile Tape NACE SP0287 Standard practice for field measurement of surface profile of abrasive blast-cleaned steel surfaces using a replica tape SSPC Technology Guide No. 12 Illumination of Industrial Painting Projects; For Applicators: Min.-20 foot candles of light and Recommended-50 foot candles For Inspectors: Min-50 foot candles and Recommended-200 foot candles SSPC ACS-1/ANSI/NACE No. 13 Industrial coating and lining specialist qualification and certification; joint training standard for coating applicators SSPC PA 2 DFT Measurement with Magnetic Gauges; Type 1: Banana Gauge Type 2: Electronic Gauge NACE SP0188 High and Low Voltage Holiday Testing